Size and Position Menu 1. Size Presets No Resizing2. Size 0.8663. Height 10004. Pixel Tracking 8585. Pixel Phase 06. Horizontal Shift 3607. Vertical Shift 2628. Reserved9. Reserved0. AdvancedSize and Position In the Size and Position Menu, you can increase or decrease the size of your image, change its proportion (aspect ratio), move the image to a specific area of the screen, and refine other related parameters. Use Size and Position controls to match the image precisely to the screen. Changes

2.LIGHT Press to illuminate the buttons. 3.ON / OFF Press to turn the projector on or off. 4.ENT (Enter) Press to select a highlighted menu item or confirm a changed setting. Note On some remote control units, this button is where the RETURN/EXIT button (item #6) appears here. 5.Cursor Buttons (, , , ) Use these buttons to select items or settings, adjust settings or switch display patterns. When no menu is present on-screen, the UP and DOWN buttons toggle through the available aspect ratios, in

This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and retain it with your other important documents. WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY: The following Vidikron product models are covered under this Limited Warranty: Vision 65, Vision 65/CineWide, Vision 65/CineWide with AutoScope Vision 75, Vision 75/CineWide, Vision 75/CineWide with AutoScope (“Product” individually and “Products” collectively). SERVICE LABOR: Vidikron will p

Figure 3-13. Composite, S-Video and Component Video Connections RS-232 Controller . Connection Use the communication cable supplied with the projector to connect a PC or home theater control/automation system (if present) to the RS-232 port on the Vision 65/75; see Figure 3-14. For more information about using this connection, refer to Serial Communications on page 67. S-VID /S-VID123457896D-Sub 9-pin femaleRJ-11 MaleCommunication Cable, RJ-11 male toD-Sub 9-pin female1234YellowYellowRedRedBlack

Input Selection Buttons: Use these buttons to select an input source directly or to enter numeric characters, as follows. 12.VIDEO (1) Press to select Composite video input as the source. 13.S-VID 1 (2)/ S-VID 2 (5) (S-Video) Press to select an S-Video input. 14.COMP (Component) (3) Press to select Component SD (480i/576i) video input as the source. 15.HD 1 (4) / HD 2 (7) Press to select a HD (RGBHV or YPbPr component) input. 16.DVI 1 (6) / DVI 2 (8) Press to select a Digital Video input. Aspect

Caution The input voltage to the AutoScope lens motor must be between 100 and 120 VAC. Do not connect the AutoScope lens motor to a 200-240 VAC power source! 4Operation 4.1 Turning on the Power 1.Turn on your source components. 2.Turn on the main power switch on the projector. 3.If this is an AutoScope-equipped projector, turn on the main power switch at the rear of the AutoScope lens motor. The lens motor power switch is located next to the AC input. 4.Press the ON button on the remote control

For the best performance, please read this manual carefully as it is your guide through the menus and operation. 1.Read these instructions. 2.Keep these instructions. 3.Heed all warnings. 4.Follow all instructions. 5.Do not use this apparatus near water. 6.Clean only with a dry cloth. 7.Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions. 8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (incl

Throughout this manual, the Vidikron Vision 10/Vision 12 DLP Projector is referred to simply as the “Vision 10/12.” Target Audience Vidikron has prepared this manual to help home theater installers and end users get the most out of the Vision 10/12. Vidikron has made every effort to ensure that this manual is accurate as of the date it was printed. However, because of ongoing product improvements and customer feedback, it may require updating from time to time. You can always find the latest ver

Focus/Zoom To focus the projected image, rotate the focus ring left or right. To make the picture larger (zoom in), rotate the zoom ring to the left, toward the Vidikron logo. To make the picture smaller (zoom out), rotate the zoom ring to the right. Zoom ringFocus ringZoom inZoom outFocusRingZoomRing Figure 4-2. Focus and Zoom Controls Shift . To change the projected image position, rotate the vertical and/or horizontal lens shift dials. Note Do not force the lens shift dials beyond their respe

9 Front / Top View ....................................................................................................................................... 10 Rear / Bottom View ................................................................................................................................. 11 Controls and Functions ............................................................................13 Control Panel ..........................................................................