When writing, always give the full model number which is on the nameplate attached to the inside of the cabinet door of the heater. When ordering repair parts or options, always give the following information as shown in the list: 1. The PART NUMBER 2. The PART DESCRIPTION 3. The MODEL NUMBER: 2927 4. The SERIAL NUMBER:________________ Before installing your heater, fill in the serial number of your heater in the space provided above. Owners Manual Model 2927 WONDERCOAL AUTOMATIC COAL BURNING CI

Some involved measurements may be required to locate the flue liner exactly. Before cutting, take time to mark the size and position of the entry port. Position the entry port so that at least 8 inches of the flue liner remains below the port. Keep in mind that coal mantels and combustible trim around the fireplace must have adequate clearances from the heater and stovepipe or must be protected in an approved manner. Also, be sure to leave at least 24" clearance between the top of the stovepipe

When writing, always give the full model number which is on the nameplate attached to the inside of the cabinet door of the heater. When ordering repair parts or options, always give the following information as shown in this list: 1. The PART NUMBER 2. The PART DESCRIPTION 3. The MODEL NUMBER: 2941 4. The SERIAL NUMBER:________________ Before installing your heater, fill in the serial number of your heater in the space provided above. OWNERS MANUAL Model 2941 WONDERWOOD THERMOSTAT CONTROLLED WO

Be sure to use a masonry chimney that it is safely constructed and in good repair. Have the chimney inspected by the Fire Department or an inspector. 6. Inspect chimney connector and chimney before and frequently during the heating season for any deposit of creosote or soot which must be removed (See Chimney Maintenance, page 18). 7. Provide air for combustion into the room where the furnace is located. If the intake is not in the same room, air must have free access to the room. 8. CAST IRON PA

This will allow for more complete combustion and less buildup of tars or soot in the chimney. 1. Set thermostat to HIGH before opening feed door. 2. Wood Fire-Model 1303- Add wood to a convenient level. WARNING! NEVER STORE FLAMMABLE LIQUIDS, ESPECIALLY GASOLINE, IN THE VICINITY OF THE FURNACE. ADJUSTING BLOWER LIMIT CONTROL SETTINGS The temperature in the plenum of the warm air furnace at which the blower turns on or turns off, is controlled by the setting of the pointers in the blower limit co

See Wiring Diagram (Fig. 12 or Fig. 13). Remove the cover from electrical junction box and connect power supply wires to wires designated, using wire nuts. The power cord supplied may be used for installation, if permitted by local codes and regulations. If the power cord supplied cannot be used, the power supply wiring must be 90 degrees centigrade in a metal cable and should be completed by a qualified installer complying with NFPA Standard No. 70 and local codes. g) Optional Plenum Fan Contro

When installing your heater, use care in handling. Clean with soap and warm water when heater is not hot. DO NOT use any acids or scouring soap, as these wear and dull the finish. PAINT DISCOLORATION WILL OCCUR IF THE HEATER IS OVERFIRED. FOLLOW OPERATING INSTRUCTIONS CAREFULLY. 13. All persons, especially children, should be alerted to hazards from high surface temperatures and kept away while in operation. Small children should not be left unsupervised when in the room with the heater. 14. Kee

7 chimney connection FIG. 4 6" SOLID DAMPER 6" BAROMETRIC DRAFT REGULATOR (OPTIONAL) THIMBLE 6" ELBOW 6" CHIMNEY CONNECTOR 6" ELBOW NON-COMBUSTIBLE WALL MASONRY CHIMNEY Before using an existing masonry chimney, clean the chimney and inspect the flue liner to be sure it is safe to use. Make repairs before attaching the furnace. See Page 4, item 5. Look at Fig. 4. The connector pipe and fittings you will need to connect directly to a masonry chimney are shown. The chimney connection should be as s

2. The installation is to be done in compliance with National Fire Protection Association installation standards: No. 89M, 90B, 211, 70 (National Electrical Code) and Uniform Mechanical Code 913, 6-4, in the states where applicable. (Their code offers connecting smoke pipe connectors into chimney with other fuel burning appliances.) 3. Rooms large in comparison with size of the appliance: a) Wood or Coal Burning Furnace needs air for combustion and circulation to house. b) Provision must be made

Logwood C226 Logwood C226Logwood C226Logwood C226Logwood C226Logwood C226 TESTED TO TESTED TOTESTED TOTESTED TOTESTED TOTESTED TOUL 1482 UL 1482UL 1482UL 1482UL 1482UL 1482& &&&&& CAN/ULC S627 CAN/ULC S627CAN/ULC S627CAN/ULC S627CAN/ULC S627CAN/ULC S627 CAUTION! CAUTION!CAUTION!CAUTION!CAUTION!CAUTION! Read All Instructions Care- Read All Instructions Care-Read All Instructions Care-Read All Instructions Care-Read All Instructions Care-Read All Instructions Care- fully Before Starting The In- fu