Francais Avant d’utiliser cet appareil, veuillez lire attentivement les instructions et assurez- --vous de les avoir comprises. Deutsch Lesen Sie diese Hinweise zur Handhabung des Gerats aufmerksam durch. Verwenden Sie es erst, wenn Sie sicher sind, da. Sie alle Anweisungen verstanden haben. Espanol Lea atentamente las instrucciones y asegurese de entenderlas antes de utilizar esta unidad. 530163281 12/11/02 2 IDENTIFICATION (WHAT IS WHAT?) Chain Adjustment Tool (Bar Tool) Primer Bulb Starter Fu

Please read the instructions carefully and make sure you understand them before using the saw. Always wear: • Approved protective helmet • Approved hearing protection • Protective glasses or visor Both of the operator.s hands must be used to operate the chain saw. Please see page 30 in your ”Chain saw operator's safety manual”. Never operate a chain saw holding it with one hand only. Please see page 30 in your ”Chain saw operator's safety manual”. Contact of the guide bar tip with any object sho

4 Start the saw and apply full throttle. Release the throttle control and check that the chain stops and remains stationary. If the chain rotates when the throttle is on idle setting you should check the carburettor idle adjustment. See the section on ”Maintenance”. 3 Chain catcher Check that the CHAIN CATCHER is not damaged and is firmly attached to the body of the saw. 4 Right hand guard Check that the right hand guard is not damaged and that there are no visible defects, such as cracks. 5 Vib

If the high speed jet H is set too lean (screwed in too far) the engine speed will be too high and cause engine damage. Do not let the engine run at full speed for more than 10 seconds. Apply full throttle and turn the high speed jet H very slowly clockwise until the engine slows down. Then turn the high speed jet H very slowly anticlockwise until the engine starts to run unevenly. Now turn the high speed jet H slowly clockwise a little way until the engine runs smoothly. H Note that the engine

speed, left/right handles, min: At max. speed, left/right handles, max: GR 2026D 1,64/26,9 1,38/35 1,10/28 2 700 11 000-11 700 10 000 0,9 KW/ 9 000 rpm Yes Yes Walbro CD Champion RCJ 7Y NGK BPMR7A 0,02/0,5 Walbro WT 1,06/0,5 13,2/6,0 93/99 2,0/2,2 2,2/3,0 1,8/2,1 2,5/3,6 GR 2032D 1,88/30,8 1,38/35 1,26/32 2 700 11 000-11 700 10 000 1,1 KW/ 8 400 rpm Yes Yes Walbro CD Champion RCJ 7Y NGK BPMR7A 0,02/0,5 Walbro WT 1,06/0,5 14,3/6,5 90/100 2,5/2,5 3,0/3,5 2,0/2,0 5,1/4,9 GR 2036 2,21/36,3 1,50/38 1

LT2115A PRODUCT NO. 960 11 01-82 401433 11.14.05 VB PRINTED IN THE U.S.A. REPAIR PARTS TRACTOR - MODEL NO. LT2115A (96011018200), PRODUCT NO. 960 11 01-82 SCHEMATIC 03054 (197428) BATTERY FUSE IGNITION SWITCH RED RED RED BLACK IGNITION UNIT HEADLIGHTS BLACK BLACK BLACK WHITE WHITE WHITE RED BLACK ORANGE BLACKBROWN BLACK BLACK BLACK STARTER M SEAT SWITCH (NOT OCCUPIED) GROUNDING CONNECTOR ATT'MENT CLUTCH (CLUTCH OFF) CLUTCH / BRAKE (PEDAL UP) SOLENOID BLACK A AMMETER RED G B S M A1 A2L HOUR METER

D Lubricating the bar tip sprocket • Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease. SAFETY INSTRUCTIONS E Needle bearing maintenance The clutch drum is equipped with one of the following chain sprockets: • Spur sprocket (A) (the chain sprocket is welded on the drum) • Rim sprocket (B) (exchangeable) Both versions have built-in needle bearing at the drive shaft, whitch has to be greased regularly (once a week). NOTE! Use only hig

SM 2055E TABLE OF CONTENTS Introduction ....................................... 3 Symbols ............................................. 4 Warning Signs ................................... 4 Safety Regulations ............................ 5 Description ........................................ 7 Installation ....................................... 16 Fuel Handling .................................. 21 Starting and Stopping.....................23 Use.................................................

(See the section on ”How to avoid kickback”.) 1 Basic safety rules 1 Look around you: • to make sure there are no people, animals or other objects nearby that might affect your work. • to make sure that none of the above might come within reach of your saw or be injured by falling trees. Follow the instructions above, but do not use a chain saw in a situation where you cannot call for help in case of an accident. 2 Do not use the saw in bad weather, such as dense fog, heavy rain, strong wind, in

The risk increases at low temperatures. Quick release There is an easily accessible, quick release fitted at the front as a safety precaution in case the engine catches fire, or in any other situation that requires you to free yourself from the machine and harness. See instructions under the heading Adjusting the harness and clearing saw. Check that the harness straps are correctly positioned. Once the harness and machine have been adjusted, check that the harness quick release works correctly.