IF IN DOUBT CONSULT A MEDICAL PRACTITIONER. 9. HOW TO PROTECT YOUR FAMILY Follow these guidelines to reduce the risk of Carbon Monoxide poisoning. (1) Know and look out for tell-tale signs that Carbon Monoxide may be present. These include: - The CO Alarm warning of abnormal levels. - Staining, sooting or discolouration on or around appliances. - A pilot light frequently going out. - A strange smell when an appliance is working. - A naked gas flame which is yellow or orange, instead of the norma

The 9V battery will last for up to 4 years in standby mode, and capable of powering the smoke detector for up to 2 years in the event of mains failure. The Ei141 is supplied with the Easi-Fit base that allows very quick and simple installation of the smoke alarm, combined with simple detector head removal and replacement. The Easi-Fit base automatically connects both mains power and battery as the detector head slides on to the Easi-Fit base. The Ei141 has other advanced features such as the abi

All units are individually calibrated and tested in CO gas in order to ensure accuracy. In addition, the sensor module can be easily changed for a new module at the end of its 5 year life. The Ei206D also has a built-in digital display which shows the CO level sensed in parts-per-million (ppm). The Ei206D is housed in a slimline casing and can be easily secured to a wall or ceiling, with a separate base- plate and all necessary fixings supplied. As well as being easy to install and maintain, the

8 B15583/R0/8/6/06 1:54 PM Page 9 NEVER IGNORE THE ALARM. Pre-Alarm: When the alarm detects over 50ppm CO the red 2 seconds. This helps locate CO leaks an indication straight away. (Without this feature the CO level would need to be at 50ppm 90 minutes for an indication to be given). Note the Pre-Alarm signal may be triggered by CO coming for example, from cooking with gas, from car engines or from nearby barbecues. This is usually not a concern, unless the Pre-Alarm signal persists until the al

An installed smoke alarm must be removed or covered fully (with a plastic bag or similar) before renovations begin. 'Ei Electronics 2003 P/N B15026 R0 RADIO SMOKE ALARMS with WIRELESS INTERCONNECT INSTRUCTION LEAFLET Contains vital information on unit operation and installation. Read and retain carefully. If you are just installing the unit, this leaflet MUST be given to the householder. MODELS: Ei 405 - Replaceable 9V Battery Ei 405C - Replaceable 9V Battery & hard wired interconnect option Ei

This leaflet must be left with the end user after installation. N.B. If the system is not being used for some tme the Control Panel power switch must be in the off position. This will prevent the battery from being totally depleted and possibly damaged. Do not turn on until it is fully wired. The systems consist of:- Ei 169 / 160 Ei 173 Control Panel (with built in strobe) Ei 174 Vibrator Pad Ei 172/160 Pattress for Smoke / Heat Alarm Interface (this requires an Easi-fit Alarm to operate i.e. Ei

This can be used for remote test & hush or manual call points. WARNING: This pattress must only be used with one of the above smoke alarms as per these instructions - otherwise the unit will not comply with the mandatory safety regulations. Installation WARNING: First disconnect the mains from the circuit to be used. 1.Choose a mounting position following the siting instructions in the Smoke/Heat Alarm leaflet. Where the incoming wiring is on the surface of the ceiling, the appropriately siz

Note: . When the battery is first connected the Alarm may sound for 2-3 seconds - this is normal. . A Smoke Alarm does not prevent fires. . Install correctly, in the center of the ceiling if possible. . Test weekly. . Replace battery yearly or when it beeps once a minute. . Plan your escape route. . Proper protection may require more than one Smoke Alarm. . If you have any doubt or query about Smoke Alarms consult the supplier or your local Fire Brigade. . Nuisance alarms can be quickly silenced

Read and retain carefully. If you are just installing this product the manual MUST be given to the householder. 1. Introduction The Ei420 can be used for two purposes: (1) It connects the Ei260ENRC Series Carbon Monoxide Alarms with RadioLINK Smoke Alarms and accessories. When the CO Alarm detects CO it will trigger all the other RadioLINK units and vice versa. It can also be used to connect Ei151TL, 154TL and 156TLH smoke/heat alarms to other RadioLINK units. Note: anytime the CO alarm is menti

The leaflet should be regarded as part of the product. If you are just installing the unit, the leaflet must be given to the householder. The leaflet is to be given to any subsequent user. INSTRUCTIONS B15583/R0/8/6/06 1:54 PM Page 2 Page CONTENTS 3 WHAT TO DO WHEN THE CO ALARM SOUNDS 4 CARBON MONOXIDE - THE SILENT KILLER! 5 WHERE TO PLACE CARBON MONOXIDE ALARMS 10 INSTALLATION 15 TESTING & MONITORING YOUR CO ALARM 19 MAINTAINANCE 21 LIMITATIONS OF CARBON MONOXIDE ALARMS 22 HOW TO PROTECT YOUR F