Our obligation under this warranty is limited to repairin.. or replacing, at our discretion, the defective instrument or any part thereof when it is returned, transportation prepaid to the Legacy Service Center at the address below. This warranty will be considered void if the unit has been tampered with, improperly serviced, subjected to abuse or misuse or if installed in a commercial vehicle. This warranty does not cover accidental damage. When returning this unit for service, please include $

Should this occur, the PROTECT LED will be illuminated. At that time, it is important that you check to determine what has caused the protection circuitry to become activated. If the amp shut off because of a thermal overload, allow it to cool down before attempting to restart. If the shutdown occured because of an input overload, or speaker short circuit, be sure to correct these conditions before attempting to restart the amp. To reset the amp, turn the REMOTE power off and on again. Power LED

Legacy has utilized the latest electronic technologies in order to deliver a superb listening experience. This innovative system has been designed utilizing a 12 V DC Negative Ground power supply. The LEGACY Blue Diamond Series amps incorporate two to eight MOSFETS in the different models. This design produces enough available voltage to supply the main amplifier sections, and still have a huge amount of reserve voltage for peak “high demand” situations. The Legacy line has been designed to ensu

This may be connected to the head unit power antenna lead. Installation Precautions This amplifier comes complete with all mounting harware required. Please remember that this is a high-power unit, which generates considerable electrical energy and heat. Therefore, be sure to install the unit in a place with sufficient airflow, a minimum of dust, and no moisture. Allow enough space around the cooling fins to permit reasonable airflow and cooling. • Before you drill or cut any holes, investigate

• Check that remote DC terminal has at least +12v DC. • Check that there is battery power on the + terminal. • Check all fuses. • Check that Protection LED is not lit. If it is lit, shut off amplifier briefly and then repower it. High hiss or engine noise (alternator whine) inspeakers. • Disconnect all RCA inputs to the amplifier(s) – if hiss/noise disappears, then plug in the component driving the amplifier and unplug its inputs. If hiss/noise disappears, go on until the faulty/noisy component

(IT) Selezionare "FLAT" per una completa risposta in frequenza. (D) Wählen Sie "FLAT" für einen compleate Frequenzbereich vor. (SP) Seleccione "FLAT" para una gama de frecuencia del compleate. (Eng) Select "HIGH" for a high frequency range. (FR) Choisissez la "HIGH" pour une gamme a haute fréquence. (IT) Selezionare "HIGH" per la risposta delle frequenze alte. (D) Wählen Sie "HIGH" für eine Hochfrequenzstrecke vor. (SP) Seleccione el "HIGH" para una gama de alta frecuencia (Eng) The cut fre

LA738 LA838 LA938 FOR YOUR PROTECTION Completely and immediately mail the Product Registration Card so that we may contact you directly in the event a safety notification is issued in accordance with the 1972 Consumer LA1038 Product Safety Act, or for other reasons Legacy may deem necessary. LA1438 LA1838 TECHNICAL SUPPORT HOTLINE Our technical department will gladly answer any questions LA2038 you may have about our products. They cannot, howevertell you the status of a repair, or handle other

Crossover Mode Switch Input Level Control Use this control to match the output of the head unit to the amplifier. If distortion is present, reduce the setting of this control. Power Supply Terminals Protects the amplifier as well as the automobile electrical system from short circuit conditions. Fuse These terminals are 14K Gold plated for high conductivity and minimum impedance loss. The terminals face upwards for easy wiring in tight situations. Speaker Terminals Plug in the Remote Bass Boost

13 13 Protection LED Indicator The protection circuitry in the amp will disable it if it senses an input overload, speaker short circuit, or thermal overload conditions. Should this occur, the PROTECT LED will be illuminated. At that time, it is important that you check to determine what has caused the protection circuitry to become activated. If the amp shut off because of a thermal overload, allow it to cool down before attempting to restart. If the shutdown occured because of an input overloa

SELECT BUTTON Press it can select VOL/BAS/TRE/BAL/FAD, and with the +/- button to adjust them, and the word which function it is selected will be indicated on LCD. 2. POWER BUTTON Press it to select you desired radio band and the word which band is selected will be indicated on LCD. (NOTE: When it is off, you can press any button to turn on the unit.) 3. MANUAL TUNING UP/DOWN BUTTON Press them to tune up or down, and the current frequency appears on LCD. 4. EJECT BUTTON Push it to eject the tape