Do not clean the dishwasher interior until it has cooled. You may want to wear rubber gloves. Do not use any type of cleanser other than dishwasher detergent because it may cause foaming or sudsing. To clean interior Make a paste with powdered dishwasher detergent on a damp sponge and clean. OR Use liquid automatic dishwasher detergent and clean with a damp sponge. OR See the vinegar rinse procedure in “Spotting and filming on dishes” in “Troubleshooting.” NOTE: Run a Normal cycle with detergent

INTRODUCTION This Job Aid, KUD01 STAINLESS STEEL DISHWASHERS, Part No. 4317288 provides specific information on the operation, diagnosis and repair of the KitchenAid KUD01 series Stainless Steel Dishwasher. KUD01 STAINLESS STEEL DISHWASHERShas been compiled to provide the most recent information on design, features, operation, troubleshooting, and repair procedures. GOALS AND OBJECTIVES The goal of this Job Aid is to provide detailed information that will enable the service technician to properl

• Para retirar el disco del soporte de discos, empuje el disco por el lado marcado hacia arriba y extraigalo del soporte de discos. Consejos: • Corte los alimentos previamente en pedazos para que quepan a traves del conducto. • Llene el conducto de manera homogenea y no presione demasiado. • Si desea procesar una gran cantidad de alimentos, hagalo por tandas pequenas y vacie de vez en cuando el tazon. 7.3 Trabajar con la cuchilla de amasar Con ayuda de la cuchilla de amasar puede amasar masa de

The float must be in place for the dishwasher to operate. Important: A small amount of water always remains in the bottom of the dishwasher (under the ultrafine filter) to keep the seal moist. The coarse strainer may be removed, if necessary. To remove, lift strainer out by squeezing center section (F) and remove. To replace, squeeze center section so clips snap into square notch. Possible Burn Hazard Heating element will be hot immediately following use. Do not touch. To avoid burns wait at

Also be sure items such as loading conveyors are not attached to or leaning on the mixer. Refer to scale manual for more specific information. 3. Mixer should be mounted on a structure of adequate strength to support a fully loaded mixer. Machine must be level and stable at the desired height. Weigh bar mounts should be fastened to this structure. 4. Manual door opener for the 3115 & 3120 can be mounted at either the front or the rear of the mixer. The following instructions will help to modify

4. Fit bowl supports over locating pins. 5. Press down on back of bowl until bowl pin snaps into spring latch. 6. Raise bowl before mixing. 7. Plug into a grounded 3 prong outlet. To Remove Bowl 1. Turn speed control to OFF. 2. Unplug Stand Mixer or disconnect power. 3. Place bowl lift handle in down position 4. Remove flat beater, wire whip, or dough hook. 5. Grasp bowl handle and lift straight up and off locating pins. RAISE WARNING Injury Hazard Unplug mixer before touching beaters. Failure t

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean: DANGERWARNING You can be killed or seriously injured if you don’t immediately follow instructions. You can be killed or seriously injured if

Consequently machinery specifications are subject to change without notice. 9/2006

34 Drain Function 1. During the Drain function, a separate drain pump motor (1) is started while the main wash pump motor continues to operate for 1 minute. This accomplishes three goals. 2. First, the jets on the underside of the lower spray arm continue to flush soils from the accumulator screen while the water is drained from the unit. (2) 3. Second, negative pressure in the main wash pump inlet chamber keeps the check valve closed, allowing the drain pump to remove soiled water from the accu