Dirty cylinder. Worn Bumper. O-rings worn in piston assembly. Disassemble and clean cylinder. Replace bumper. Purchase Bottom Repair Kit Replace piston assembly. On the NBSNC2x4 contact an *AWSC for correct part. All other nailers purchase Bottom Repair Kit. Weak Drive. Inadequate air supply. Worn piston assembly. Check PSI and CFM. Replace piston assembly. On the NBSNC2x4 contact *AWSC for correct part. All other nailers purchase Bottom Repair Kit. NBSNC2X4 leaving a 1/4” indention. Driver blad

SNC1002x4 Pull feeder shoe back into "locked" position. 6. NF2502X4, NB1252X4, NB2002X4, and SNC1002X4 Replace nose cover and latch into place. NBSNC2X4 Replace nose cover. 7. Reload fasteners into magazine. Refer to Feeder Magazine Latch 5. Using pliers remove fasteners. Loading the Tool section in this manual. PAGE 13 FASTENER JAM INSIDE MAGAZINE: SNC1002x4 Pull feeder shoe back into "locked" position. 1. Disconnect tool from air hose. 2. NF2502X4, NB1252X4, NB2002X4, NBSNC2X4 Release the maga

NOTE: The meter housing will be full of liquid so some means should be available to catch what drains from the case and lines. To remove gears (22-25), remove three retaining rings (20) and drive key (21). Withdraw the drive shaft and gear (14), spacer (15), and all parts of bearing and seal assembly (26). Remove the nylon washer from item 26 and note its location. Remove both oilite bearings and both O-rings from bore in register housing. Using new parts, which consist of a new nylon washer, 2

El grifo no esta completamente abierto o la unidad no recibe un volumen completo de agua. El filtro de la pantalla esta obstruido. Asegurese de que el grifo esta completamente abierto. Revise la conexion de la manguera del jardin y asegurese de que cumple los requisitos que se describen en el Manual del propietario. Limpie el filtro de la pantalla como se indica en la Seccion , del Manual del propietario. La luz azul “Alta” (High) no se enciende. NOTA: La luz azul “Alta” (High) solo se encendera

4. Flush wand assembly backwards with water or compressed air. 5. If pressure is still too high, repeat steps 2-4. 4. CHECKING OIL: The pump is shipped with the correct amount of oil in it. This pump should never need any oil added or changed unless it develops a leak. A 30 weight non- detergent oil can be used in this pump (approximately 6 oz.). If pump is leaking oil take to an Authorized Service Center. HIGH PRESSURE HOSE: Damaged high pressure hoses can burst which can cause a potentially ha

TECNICAS DE LIMPIEZA Cuando se procede a la limpieza con la hidrolimpiadora, se pueden efectuar diferentes operaciones solo con el agua; en muchos casos, sin embargo, es conveniente utilizar tambien un detergente. El uso de un detergente asegura un tratamiento inmediato de la suciedad, permitiendo al agua con alta presion penetrar y eliminar eficazmente la suciedad. La posicion de baja presion suministra una aplicacion delicada del producto quimico. Recomendamos esta posicion tambien para enjuag

2. Exhaust Muffler-Allows hot exhaust to exit the engine. 3. Siphon Tube & Filter- Used to pick up detergents, degreasers, etc. for cleaning. 4. High Pressure Hose-25' x 1/4" dia. high pressure hose used to transport water from pump to gun. 5. Quick Connect Coupler-Used to attach water hose to pump. 6. Pressure Washer Gun-Used to control flow of water coming from pump. 7. 3.5 HP Tecumseh Engine- This engine is shipped without oil. Included with this pressure washer is a copy of the Engine Manufa

8) © Installing the Handle (see pg. 8) Instalación del mango (ver pág. 8) ©Assembling the Trigger Handle (see pg. 8) Armado de mango del gatillo (ver pag. 8) ©Connecting the High Pressure Hose to the Trigger Handle (see pg. 8) Cómo conectar la manguera de alta presión al mango del gatillo (ver pág. 8) © Connecting the High Pressure Hose to the Pump (see pg. 9) Cómo conectar la manguera de alta presión a la bomba (ver pág. 9) ©Connecting the Garden Hose to the Pressure Washer (see pg.