Step 5: Place the socket on the nut. To begin tightening the nut, press the TRIGGER. Step 6: If the Air Ratchet stalls while tightening, do not continue attempts to tighten the nut with the Air Ratchet. DO NOT raise the outlet pressure of the air compressor. Use the appropriate tools and methods to tighten the nut. Step 7: When the nut has been tightened, remove the Air Ratchet and socket. Step 8: If available, check the recommended torque specification for the nut. You should use a torque wrenc

It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Addresses practices not related to personal injury. imPORtant SaFe

Route the air hose along a safe route 2. to reach the work area without creating a tripping hazard or exposing the air hose to possible damage. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working. Secure loose workpieces using a vise 3. or clamps (not included) to prevent movement while working. There must not be hazardous objects 4. (such as utility lines or foreign objects) nearby or in the surface being cut that will present a

Follow instructions for lubricating and changing accessories. Inspect tool cords and air hoses periodically and, if damaged, have them repaired by an authorized technician. The handle must be kept clean, dry, and free from oil and grease at all times. 10. Disconnect air supply. Disconnect air hose when not in use. 11. Avoid unintentional starting. Be sure the Trigger (#8) is not depressed when carrying the Air Hammer. 12. Stay alert. Watch what you are doing, use common sense. Do not operate any

Failure to do so can result in serious injury. Save this manual. Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be

All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. 30224 HARBOR FREIGH TOOLS For technical questions and replacement parts, please call 1-800-444-3353. Manual Updated 09/05 IMPORTANT: Before using for the first time, the spray gun must be cleaned using a solvent based thinner. If not removed, the red oil used by the manufacturer for testing and corrosion protectio

® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353. TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE. REV 11h PRODUCT SPECIFICATIONS Item Description Product Compatibili

To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. (California Health & Safety Code § 25249.5, et seq. ) Warning! Operation of equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. Unpacking When unpacking, check to make sure the parts listed on page 6 are included. If any parts are missing or

4. Apply an adhesive-backed sanding head (not included) to the Pad. Cut the sanding head to size if necessary. 5. Secure all workpieces with a clamp or vise so that both of hands are free to operate the Sander. 6. Connect the Sander to the air compressor hose at the Regulator Assembly (30). 7. Grip the Handle with your left hand and the Body (13) with your right (reverse if you are left-handed). Depress the Trigger (28) with your left hand to turn the tool on. SKU 96573 For technical questions,