PRODUCT DESCRIPTION Linear’s Xtended Range FM receivers and transmitters are designed for use in various wireless remote control applications. When the Model XR-16 receiver detects a signal from its companion transmitters, it will verify the digital code, activate the correct output channel, and trigger the remote device connected to the receiver. The XR-16 receiver has full supervision capabilities. If the “status” option for a channel is selected, the receiver expects hourly status signals fro

The DVS-2400 Console incorporates many advanced and sophisticated features. The system can be expanded and customized to fit the installation’s specific needs. The DVS-2400 Console and its accessories are designed and manufactured by the oldest wireless security company in North America. You can look ahead to many years of reliable service with this Console and its accessories. Many insurance companies offer discounts on homeowners and renters policies when a security system is installed. Discou

This transmitter can be used in a limitless number of wireless remote control applications. Triggering the transmitter with its built-in magnetic switch, an external switch or an external glass break detector sends a digitally coded wireless signal to its companion receiver. Pressing the transmitter’s case sends a test transmission. The digital DX code format features over a million possible codes. The DX transmitters are precoded at the factory to unique codes, so no field coding is required. T

Pressing a button on the transmitter sends a digitally coded wireless signal to its companion receiver. To send a complete signal, press the transmitter button for a minimum of 2 seconds. The digital DXS code format features over a million possible codes. The DXS transmitters are precoded at the factory to unique codes, so no field coding is required. The multi-button transmitters send variations of their preset codes depending on which buttons are pressed. Transmitters can send a signal for up

PRODUCT DESCRIPTION Linear’s Xtended Range FM receivers and transmitters are designed for use in various wireless remote control applications. When the Model XR-4 receiver detects a signal from its companion transmitter, it will verify the digital code, activate the correct output channel, and trigger the remote device connected to the receiver. The XR-4 receiver has full supervision capabilities. If the “status” option is selected, the receiver expects hourly status signals from its transmitter

ZONES ARE NORMALLY OPEN WITH END-OF-LINE RESISTORS 2. LOW BATTERY AND STATUS OUTPUTS ARE COMBINED TO TRIGGER ZONE 4 AS TROUBLE TO +12 VOLTS TO RECEIVER OUTPUT N.C. N.O. COM 12 VOLT RELAY 1N4001 DIODE EXAMPLE 4-ZONE CONTROL PANEL HOOK-UP EXAMPLE BEEPER HOOK-UP TO RECEIVER OUTPUT TO +12 VOLTS PIEZO BEEPER EXAMPLE L.E.D. HOOK-UP 1K OHM L.E.D. TO +12 VOLTS TO RECEIVER OUTPUT JUMPER IN THIS POSITION (FACTORY SETTING) CAUSES A MOMENTARY 3/4 SECOND OUTPUT WITH EACH ACTIVATION SET OUTPUT JUMPERS FOR EAC

Care must be taken to prevent injury or death during installation and operation of the garage door and garage door operator. 1 Check the Door Balance 1 From outside the garage, slowly open the door all the way, and then close it all the way. Notice if there is any binding, sticking or rubbing. The door should move smoothly in both directions. 2 Raise the garage door about halfway up. Carefully release the door and see if the door balances. It should stay in place. Close the door. IMPORTANT: If

See Figure 1 for details of the telephone jack wiring. A single ended 8-conductor modular line cord is used to connect the PERS console to the telephone jack. Plug the LINE and PHONE plugs into the appropriate jacks on the PERS console. See Figure 2. Route the cable away from the jacks via the internal raceway. Then install the 8-position plug into the telephone company jack. Testing Test the PERS console by first calling the central station and informing them that a test is going to be perfo

PLAN INSTALLATION INTRODUCTION The AM-KP keypad is designed for use with Linear’s AM/II access control system. The keypad is housed in a rugged cast aluminum enclosure. The die-cast keys have bright, easy-to-read yellow graphics. Each key has a positive tactile “click” feel when pressed. An internal sounder signals when a key is pressed. The keypad can be mounted to a pedestal or directly to a wall. A keylock secures the keypad to the mounting backplate. An incandescent panel lamp lights the