To prevent triggering of smoke alarms, ventilate the room in which the unit is installed. IMPORTANT: Read all instructions carefully before starting installation. Failure to follow these installation instructions may result in a possible fire hazard and will void the warranty. Save this manual for future reference. Please read this manual before installing and using the appliance. WARNING: Any modification to this unvented gas heater or its controls can be dangerous. Improper installation or use

INSTALL FOAM GASKET FLUE ADAPTOR PLASTIC GASKET THREADED CONNECTOR Attach flue adaptor to back of heater with four (4) screws. Note: No PVC cement is needed to install flue adaptor kit. Install plastic gasket and screw threaded connector to the flue adaptor. When these connections are made, continue with your vent run. Cement all PVC joints on vent run. PVVK-SH HORIZONTAL VENT ADAPTOR KIT Page 24 24820-1-0409 HORIZONTAL EXAMPLES FOR COLINEAR DIRECT VENT Figure 27 Enhanced top view of Figure 26 F

— WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor'sphone. Followthegassupplier's instructions. • If you cannot reach your gas supplier, call the fire department. — Installation and service must be performed by a qualified installer, service agency or the gas supplier. WARNING: If the information in this manual is not followed exactly, a fire or explos

11 West 42nd St. Batterymarch Park New York, NY 10018 Quincy, MA 02269 12409-2-0403 Page 7 CLEARANCES CLEARANCES Minimum Dimensions For Solid Fuel Burning Fireplaces UL127 Factory Built Fireplaces (Figure 2) Model ABCD VFYM-16 18" 13" 24" 18" VFYR-16 18" 13" 24" 18" VFYM-18 17" 14" 28" 17" VFYR-18 17" 14" 28" 17" VFYM-24 23" 14" 30" 18" VFYR-24 23" 14" 30" 18" VFYM-30 26" 14" 34" 20" VFYR-30 26" 14" 34" 20" Figure 2 The dimensions shown and defined in the fireplace manufacturer’s instructions ar

Figure 12 GAS CONVERSION INSTRUCTIONS Warning: Conversion must be done by a qualified service technician. Conversion Instructions from Propane (LP) gas to Natural gas. 1. If installed, turn off gas supply to outdoor gas fireplace. 2. If installed, remove Propane (LP) gas hose from gas valve. 3. Remove electrode wire piezo ignitor. 4. Remove thermocouple from gas valve. 5. Remove two (2) bolts and two (2) nuts from valve bracket at bottom of outdoor gas fireplace. 6. Carefully remove valve bracke

Place propane tank from cooker so that the hose length will not be in the way. Keep all connections and fittings clean, replace any damaged parts. 19. Never store the propane tank near high heat, open flames, direct sunlight or where high temperature exist. Assembly Instructions REQUIRED TOOLS: Pliers or adjustable wrench and screwdriver. 1. Bolt legs in place by inserting short bolts through holes in corners of main top, then through slot at top of leg. Screw nuts onto the bolts. Attach drip pa

This should consist of a vertical length of pipe tee connected into the gas line that is capped on the bottom in which condensation and foreign particles may collect. The use of the following gas connectors is recommended: — ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing and Fittings — ANS Z21.45 Assembled Flexible Appliance Connectors of Other Than All-Metal Construction The above connectors may be used if acceptable by the authority having jurisdiction The state of Massachusetts re

3. Re-open brass control valve 1/4 turn. 4. Keeping hands and face away from the top of the burner, light with a fireplace match or long-nose lighter. 5. Adjust the brass control valve for desired flame height. R-3088 Empire Comfort Systems, Inc. . 918 Freeburg Avenue . Belleville, IL 62220 Page 1 SECTIONAL PARTS FOR GAS STOVE SP-010 SP-011 SP-012 SP-064 SP-063 SP-065 SP-066 SP-067 SP-013 SP-014 SP-015 P-220 P-219 SW2-1 SW3-1 R-3445 SP-034 SP-062 P-221 R-3337 SP-028 SP-055 SP-016 S-1377 R-3339S-

(This shuts off flow of gas from the regulator to the burner. 2. Open LP cylinder valve or gas supply by 1/4 turn. This allows gas into the regulator and stops it at the brass control valve. 3. Apply gas detector fluid (or soapy dishwashing solution) on all connections, especially around the regulator, valve and POL-cylinder GRATE BURNER TOP 1/4" BOLT 1/4" HEX FLANGE NUT BODY LEG Model No. SE-200 w/SLK-28 VALVE KNOB connection. Any bub-bles that appear indicate a gas leak. If so, turn off gas an

. . . . . . . . Safety information Danger of electrocution! • Connect the appliance only to a 50 Hz grounded power socket with mains voltage of 230 V~ and that has been installed according to instructions. • Do not bend or squeeze the power cord. •To disconnect, always pull out the plug at the power socket, do not pull on the power cord. • Never touch the chimney, power cord and power plug with wet hands. • Do not use extension cables. • Do not wind the power cord around the casing of the chimn