Printed in U.S.A. All product names are trademarks of their respective companies. Table of Contents Title Page Introduction..................................................................................................................... 1 How to Contact Fluke ..................................................................................................... 2 Connecting to a HART Transmitter ................................................................................ 3 Supported vs. Ge

The result is a reduction in cross color interference and an improvement in the picture quality. The R-G-B output offers the primary colors red, green, and blue including composite sync and sub-carrier signals at 5 BNC sockets at the rear side. Service is done at the component level, so it is not necessary to exchange a complete module. In addition the mechanical concept allows quick access to all parts for service purposes; all units are plugged into the motherboard. (GB) 2-2 GENERAL PM 541

La somme L+R donne lieu à un niveau d’environ -17 dB (14,1 %) en-dessous du niveau d’entrée maximal basse fréquence. Ce signal combiné est utile pour aligner l’affaiblissement diaphonique stéréo de décodeurs BTSC, par ex. Philips TDA 9855 ou TDA 3833. SAP: fmod = 1 kHz, avec 70 % du niveau d’entrée basse fréquence Ce signal test permet de mesurer le facteur de distorsion harmonique total lors du traitement SAP du côté récepteur. Type de test 2: Stéréo: L = 300 Hz, R = 8 kHz Les deux signau

All rights reserved. All product names are trademarks of their respective companies. User’s Guide – version 3.5 NetFlow Tracker Contents SOFTWARE LICENSE AGREEMENT 5 INTRODUCTION 15 What is NetFlow? 15 What is NetFlow Tracker? 15 Features and Benefits 15 INSTALLATION 17 Minimum System Requirements 17 Operating System Support 17 Pre-installation Checks 17 Installation on Microsoft Windows 18 Installation on Linux 19 Post-installation Tasks 19 USING NETFLOW TRACKER 21 Real-time Data 21 Long-term D

Amp. 70 % 100 % 30 % 24 % 48 % 100 % 120 % 112 % 80 % Lead I reference Performance waves and R wave detection Lead # I II III V1 V2 V3 V4 V5 V6 Ref. Amp. 100 % 150 % 50 % 100 % 100 % 100 % 100 % 100 % 100 % Normal Sinus waves Lead # I II III V1 V2 V3 V4 V5 V6 Ref. Amp. 100 % 150 % 50 % 24 % 48 % 100 % 120 % 112 % 80 % ECG Normal Sinus Rates................................................................... 10 to 360 (by 1) BPM ECG High Level Output (BNC Jack) Amplitude Range ....................

& Date: 1, 2/2008 CD PN: 3028681 © 2008-2009 Fluke Corporation. All rights reserved. Printed in the U.S.A. Impulse 6000D/7000DP Users Manual Supplement Change #1, 46470, 46697, 47714, 48007, 49680 Replace pages 31 through 35, with the following: Defibrillator Analyzer Specifications Energy Output Measurement Compatible Defibrillator Waveshapes ................ Lown, Edmark, Trapezoidal, DC Bi-phasic, and AC Pulsed Bi-phasic Note AC Pulsed Biphasic waveform has not been approved in the United Sta

Materials for Cleaning the High Range Piston Cylinder 1. Prepare a clean work area near a running tap water source. 2. Prepare several sets of folded wipers as shown in Figures 6-2 through 6-4. Two wipers can be folded together for wiping the outside of the piston and cylinder. Prepare several twisted wipers as shown in Figures 6-10 through 6-12 to wipe the bore of the cylinder. 3. Disassemble the piston/cylinder assembly. 4. Insert the retaining clip from the bottom of the piston into the insta

This manual is distributed as an electronic manual on the following CD-ROM: CD Title: 1652C/1653B/1654B CD Rev. & Date: 9/2010 CD PN: 3798444 © 2010 Fluke Corporation. All rights reserved. FLUKE 1652C/1653B/1654B Users Manual Supplement Change #1, 56800 On page 3, add the following bullet: • Do not use in CAT III or CAT IV environments without the protective cap installed. The protective cap decreases the possibility of arc flash caused by short circuits. On page 6, under Operating th

• Be sure the test leads and switch are in the correct position for the desired measurement. • Never measure resistance in a circuit when power is applied. • Never touch the probes to a voltage source when the test leads are plugged into the 10 A or 300 mA input jack. • Never apply more than the rated voltage between any input jack and earth ground. • Be careful when working with voltages above 60 V dc or 30 V ac rms. Such voltages pose a shock hazard. • Keep your fingers behind the finger guard

All rights reserved. Printed in The Netherlands. All product names are trademarks of their respective companies Using the Interface Cable PC Requirements - USB 1.1 (or higher) port on the PC. - Windows XP/ 2000/ Me/ 98 Second Edition. Installing the USB- IR cable drivers - Log into an account with Administrator privileges (Windows XP or Windows 2000). - Plug the USB cable into an USB port. - Windows will respond that it has "found new hardware", and the Windows Hardware Wizard dialog will appear