THIS PARTS GUIDE IS FOR REFERENCE ONLY. REFER TO THE INSTALLATION MANUAL FOR FULL ASSEMBLY INSTRUCTIONS. x 1 x 2 3” Wood Screw x 4 Flat Washer Hanger Bracket Assembly x 2 1.5” Wood Screw Parts List Model # 28665 28642 Asm. Dwg. # 99673-01 99673-02 Finish Brushed Nickel New Bronze Item Name Qnty Part # * Hanging System Kit 1 96970-09 96970-30 Ceiling Plate Canopy Canopy Trim Ring Hanger Ball / Downrod Assembly Setscrew Low Profile Washer Canopy Screw Wood Screw 1.5” Wood Screw 3” Flat Washer Moun

4 HEAT TEMP 33 ¦ Auto Recovery will be canceled and change to Home Today mode if HOME TODAY is pressed during the recovery process. ¦ Auto Recovery will be canceled and change to Temporary Manual Override mode if the setpoint is adjusted during the recovery process. ¦ If the system is changed between heat and cool then the thermostat will recalculate Auto Recovery again. Setpoint temperature will be changed to the opposite system’s comfort temperature if the recovery entry criteria are still met

Reference the Trouble Shooting guide in your Instruction Manual. 2. Call your Local Service Center. 3. Call Technical Support at 901-248-2222. For additional information on: Hunter Products Trouble Shooting Dealer Location Service Center Locator Call 1-800-448-6837 R If parts are missing or damaged call 1-888-830-1326. PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE. Model Name Catalog No. Serial No. Date Purchased Where Purchased PARTS GUIDE Using the Parts Guide below, check to make sure all pa

THIS PARTS GUIDE IS FOR REFERENCE ONLY. REFER TO THE INSTALLATION MANUAL FOR FULL ASSEMBLY INSTRUCTIONS. Hardware (Drawn to Scale) x 2 3” Wood Screw x 2 1.5” Wood Screw x 4 Flat Washer x 2 Lockinig Screw x 4 Canopy Screw x 4 Mounting Isolator Screw, Blade Iron Armature x 11 Blade Grommet x 16 Screw, Blade Assembly x 16 Balancing Kit x 1 Screw, Switch Housing Assembly x 3 Wire Connector x 4 Screw, Machine, 6-32 x 3 Fan Parts (Not Drawn to Scale) Hanger Bracket Assembly Blade Assembly Switch Housi

6. Los ventiladores canalizados siempre deben descargar al aire libre. 7. Si va a instalar esta unidad en una banera o ducha, debe tener una marca que indique que es apropiado para ese uso y debe conectarse a un circuito derivado protegido por un GFCI (interruptor automatico de falla a tierra). 8. Nunca coloque un interruptor donde pueda ser alcanzado desde una tina o una ducha. 9. Instale el ventilador por lo menos a 5 pies (1.52 m) por encima del piso. 10. Esta unidad se debe poner a tierra. 1

2 1 I H Afloje los tornillos. Apague la fuente de alimentacion. 3 4 H E Retire el material de embalaje. Retire el motor/soplador/soplador del alojamiento. 5 6 Retire las cubiertas de las puntas de tornillo precargadas. Retire las puntas de tornillo precargadas hasta que esten a nivel con el lado del alojamiento. 7 8 F G Retire la cubierta del cableado. Retire el tornillo de la cubierta del cableado. 9 10 E C B Retire el primer tapon metalico de acceso del cableado. Utilice el segundo si es neces

Tiempo estimado de ensamblaje: entre 30 y 60 minutos Antes de la instalacion Verifique todos los componentes. Si estan danados, llame al 1-888-830-1326 para un reemplazo. Instalacion para construccion nueva Vaya al paso A1, pagina 4 Construccion existente Vaya a Instalacion para construccion existente, pagina 8 NOTA: Retire todo el material de embalaje antes de la instalacion. 41717-02 05/31/2006 41717-Span_05.31.06.indd 17 5/31/06 3:54:40 PM A1 D Retire las puntas de tornillo precargadas hasta

THIS PARTS GUIDE IS FOR REFERENCE ONLY. REFER TO THE INSTALLATION MANUAL FOR FULL ASSEMBLY INSTRUCTIONS. Using this Parts Guide, make sure all parts are included in the box. If parts are missing, DO NOT RETURN THIS ITEM TO THE STORE, call 888-830-1326 for assistance. THIS PARTS GUIDE IS FOR REFERENCE ONLY. REFER TO THE INSTALLATION MANUAL FOR FULL ASSEMBLY INSTRUCTIONS. Parts List Model # 21100 Asm. Dwg. # 99473-01 Finish Brushed Nickel Item # Item Name Qnty Part # 1 * Hanging System Kit 96970-0

Reference the Trouble Shooting guide in your Instruction Manual. 2. Call your Local Service Center. 3. Call Technical Support at 901-248-2222. For additional information on: Hunter Products Trouble Shooting Dealer Location Service Center Locator Call 1-800-448-6837 R If parts are missing or damaged call 1-888-830-1326. PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE. Model Name Catalog No. Serial No. Date Purchased Where Purchased PARTS GUIDE Using the Parts Guide below, check to make sure all pa

B25 Encienda la fuente de alimentacion. ENCENDIDO APAGADO B26 Pruebe el motor. Si el motor no funciona, verifique la conexion del enchufe. B24 J Asegure el motor apretando los 2 tornillos. 42929-02 10/26/2010 C11 VENTILADOR EXISTENTE C12 E F Construccion existente – accesible desde arriba 32 SIN VENTILADOR EXISTENTE 8” 8 1/2” O Retire el ventilador existente y asegurese que la abertura sea suficientemente grande para acomodar el alojamiento del motor nuevo (8” x 8 1/2”). Recorte una abertura par