Additional reinforcement from continuous fiberglass overwrap. Underdrain design maximizes softener’s capacity, reduces pressure loss. • Softening Media—High quality resin provides stability and uniform size for top performance and long life. • Choice of Cycle Controllers—Regeneration cycle may be initiated by timeclock any or every day of the week. Optional meter starts cycle after preset volume of water has been softened. • Positive Motor-Driven Regeneration Valve–Motor driven piston is reliabl

5. Inserte el nuevo filtro alineando los tubos de salida en el filtro con los orificios de entrada del cuerpo del surtidor y presionando suavemente hacia adentro y abajo. Una vez completa la instalacion del cartucho del filtro, el surtidor portatil emitira tres pitidos y el indicador de vida del filtro volvera automaticamente al punto inicial. 6. Reinstale la cubierta del filtro colocando la lengueta de alineacion en la muesca correspondiente en el cuerpo principal del surtidor portatil y empuja

Test Water Feed Product Hardness Iron Hydrogen Sulfide Chlorine TDS Other Comments: Bypass Valve Bypass in Service or Bypass? Condition of bypass valve Operation OK? Control Valve Condition of Eductor (Sulfur-Cleer™) Condition of Solution Valve (Sulfur-Cleer™) Condition of Seal Pack and Brine Piston Condition of Solenoid Valve Condition of Motor: Condition of Flow Control Condition of Switches: Condition of Check Valve Condition of Compressor Output PSI Control settings Before After Check / rese

Notice: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts. For installations in Massachusetts: Massachusetts Plumbing Code 248 CMR shall be adhered to. Consult your licensed plumber for installation of this system. The use of saddle valves is not permitted in Massachusetts. Check with your public works departm

Equipment Needed • Safety glasses • Rubber gloves, sanitary • Wash cloth, clean and lint-free • Liquid dish soap • Household bleach - unscented only (5-1/4% sodium hypochlorite) • Plastic storage bag • Manual air pump • Plastic bucket • Plastic bowl • Silicone lubricant, FDA approved Have all components and supplies on-hand and ready before beginning procedure. A clean work area and equipment are essential to properly clean and/or sanitize the system (i.e., clean hands, tools, work surface and c

• Single, Duplex, Triplex, or Quad Configurations • Regeneration initiation by choice of time clock, meter or differential pressure switch. • Carbon Filters – For reduction of organics (flow rates up to 39gpm), or chlorine (flow rates up to 77gpm). • Depth Filters – Flow rates up to 193gpm. • Top-Mounted Control Valve – Keeps plumbing connections simple and adaptable. Full flow porting with rounded orifices and wide-open cartridges promote good flow characteristics and low pressure fluctuations.

Failure to do so may result in cracking of the filter and water leakage. NOTE: Make certain that installation of this system complies with all state and local laws and regulations. FOR COLD WATER USE ONLY. MAINTENANCE: Contact your area retailer for replacement cartridges and pricing or call Culligan Customer Service at 800-634-1455 for the nearest dealer. Change cartridge every 2500 gallons or approximately every 12 months. Filter Installation Instructions (For copper or plastic tubing) NOTE:Sh

The display will blink “SLtP” if set to English or “SLtG” if set to Metric for 3 seconds and then display the salt dosage. Adjust the setting with the “+” or “-” key (3-24 lbs.) (1-10 kgs.) Note: This option will not show if the control is set to Filter mode. Step 4 – Programming Backwash Time Press the “Status” key after programming salt dosage. The display will blink “bw” for 3 seconds and then display the backwash time in minutes. Adjust the setting with “+” or “-” key. (1-40 minutes) Program

**The efficiency rated dosage is only valid at the 6.0 lb. salt dosage. Buyer Signature _____________________________________________ Date __________ Seller Signature _____________________________________________ Date __________ Performance Data Sheet Culligan knows the more informed you are about your water treatment systems, the more confident you will be about its performance. It’s because of this and more than sixty years of commitment to customer satisfaction that Culligan is providing this

It is recommended that, before installing a water treatment system, you have your water supply tested to determine your actual water treatment needs. This system has been tested according to NSF/ANSI 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42/53. Model FM-15 Substance Influe