Do not stake the tent down yet. In windy conditions, we recommend that a narrow end should face into the wind and that you stake down one corner of this end. See fig.1 Join the shock-corded poles together. Try to prevent pole sections from snapping together, as this can damage the pole ends. Make certain each insert end has seated firmly into each plain end. At the front corner of the tent; [with the yellow web]- A, fit the post end of one of the aluminum poles into the web grommet. Angle the po

2 front fig.3 fig.4 fig.5 fig.6 fig.7 fig.8 fig.9 fig.10 A E E F F C B D Component List: 1 Tent Body, 1 Tent Fly, 2 Front Poles, 2 Rear Poles , 1 Spanner, 1 Center Hoop, 2 Junction Tubes, 1 Carry Bag, 1 Pole Bag, 1 Stake Bag w/ Stakes • Unroll and unfold the tent with the floor on the ground. Remove the fly and set it aside. Do not stake the tent down yet. In windy conditions, we recommend that an end should face into the wind and that you stake down one corner of this end. See fig.1. • Join the

Open the low vent/window to admit cool air, allowing the warmer air out through the high roof vents. When rain and wind prevent the low vent from being opened, the high door vent can still be used. Fly overhangs or vestibules protect it. ULTRAVIOLET LIGHT: Ultraviolet light damage to tent fabric is caused by excessive exposure to sunlight. While our fabrics are UV resistant, any synthetic fabric is susceptible to UV degradation. UV damage will cause nylon and polyester to become brittle and tear

GUY LINES: Do not depend upon staking alone to keep your tent secure during high winds. Most tent models have built-in loops or rings at optimal guy out locations. It’s important to put in the extra time guying out your tent. Correctly done, it can save your tent during exceptional weather. • Make sure that the top fly is securely attached to the tent frame. Ties, hook and loop, or dog-bones and elastic loops are sewn to the underside of the fly for this purpose. • Attach parachute cord to the l

These actions may cut the shock cord and/or damage the pole ends. 1. Unpack the tent bag and separate the components. Unfold the tent and lay it out with the floor on the ground and with a grommeted web in each corner. Pull the tent into a rough rectangle. Do not stake down the tent just yet; but in windy conditions, stake down one corner that faces into the wind. 2. Assemble the three shockcorded tent poles. Carefully seat each section. Try to keep the poles from snapping together as this can d

• Once the tent body is erected, stake it out before the fly is put on. This enables you to square the tent up to ensure that the fly goes on properly and that the seams align with the frame. Pull the base of the tent taut between each web stake out loop or ring & pin. Make sure that all corners are square. It is important that you don’t stake the tent out too tightly. You will know it’s too tight, if the door zippers can not be easily operated. Drive stakes through the web loops, or with ring &

fig.5 fig.4 fig.1 fig.2 fig.3 fig.6 fig.7 • Unpack the tent bag, pole bag and separate all of the components. Unroll and unfold the fabric with the Eureka! label up. Locate the hub fitting attached to the center of the roof. See fig.1. Important: Align the hub arms to match the layout of the fabric. • Make sure the hub and fabric are still aligned. Then, insert the proper corner ring & pin into the bottom pole section. See fig.3. • Assemble all of the shockcorded poles. Check and make sure that

• The tent bag should be used only as a carry sack and not for storage. COLOR TRANSFER: • Do to the nature of tent fabrics, color can transfer from darker to lighter fabrics when the two fabrics are in contact over time when wet, damp or exposed to the combination of moisture and high heat. This does not effect the tent's performance. To prevent / minimize color transfer, always make sure your tent is completely dry prior to packing and storage. CLEANING: • Clean the tent by setting it up and wi

• Do not attempt to remove the stakes by pulling on the tent becket loop, as this could cause the fabric to tear. The best way is to pry on the stake itself. Staking in special conditions: • Sand. Use long, broad stakes with plenty of surface area in loose soil. • Hard, Rocky, or Frozen Soil. Steel stakes work best. Store steel stakes separately. Their sharp edges can cut fabric and leave rust stains, which might damage your tent. • Snow. Use “dead man” anchors. Tie tent to buried objects (branc

PLAN AHEAD AND PREPARE 2. TRAVEL & CAMP ON DURABLE SURFACES 3. DISPOSE OF WASTE PROPERLY 4. LEAVE WHAT YOU FIND 5. MINIMIZE CAMPFIRE IMPACTS 6. RESPECT WILDLIFE 7. BE COURTEOUS OF OTHER VISITORS SEAM SEALING: We recommend use of a sealer such as Kenyon Seam Sealer 3 or McNett Outdoor SeamGrip®. • Work in a fully ventilated area. • Set the tent up or lay the tent out flat. Taut seams allow for even application and penetration of the sealer. • Decide which seams need to be sealed. For example, sea