Connect the loudspeaker cables to the Showcase Amplifier channel output binding posts (6) located on the back panel. The Showcase 5 uses only outputs 1-5 and has caps on the speaker binding posts for channels 6 and 7. The Showcase 6 uses outputs 1-6 and has caps on the speaker binding posts for channels 6 and 7. The binding post terminals accept spade lugs, bare wire, or pins. Use the red terminal for the positive connection and the black terminal for the negative connection. Tighten loudspeaker

A blend of fine traditional craftsmanship and leading-edge technology. A leader in American-made musical instruments and equipment for over a quarter of a century. Contents Introduction................................................................... Page 2 Features................................................................................ 2 Construction.......................................................................... 3 Controls...............................................

BEFORE USING THIS APPLIANCE, READ BACK COVER FOR FURTHER WARNINGS. TM Citation Operating Guide GENERAL DESCRIPTION The Citation™ incorporates the features needed to reproduce the complex tonalities and dynamics necessary for today’s guitarist. Our extensive Research and Development program has recently yielded several significant and, we feel, pivotal breakthroughs in amplification of the electric guitar. For many years, both guitaristsand instrument amp manufacturers have diligently sought

Experimentation with, the unique middle circuit will show that it is much more effective than conventional circuits. (8) The treble control varies the high end response of the amplifier. (9) The reverb control determines the amount of delayed signal (reverb) blended into the output. This circuit is able to produce tremendous sustain and clarity by properly damping the driver coils of the reverb unit. The reverb is effective in BOTH channels. (10) The master volume control is very useful for o

(3) El alambre marrón debe conectarse a la terminal marcada con la letra L o el color rojo. 2. FUSIBLE PRECAUCIÓN: EL FUSIBLE SOLAMENTE DEBE SER REEMPLAZADO CUANDO EL CABLE DE ALIMENTACIÓN HAYA SIDO DESCONECTADO DE SU FUENTE DE ALIMENTACIÓN. Un fusible de 5 Amp ha sido colocado dentro de la tapa del compartimiento del fusible. Debe ser reemplazado con uno del mismo valor y tipo para evitar cualquier daño al equipo y para no cancelar la garantía. Si el amplificador quema fusibles continuamente,

Source ±99 Reserved BA Reserved for future use Osc3ModRng BB Pitch Mod. range for Mod Source 1 & 2 0-14 Osc3Mods BC Osc3ModlSens BD Sensitivity to Mod source 1 ±99 Osc3Mod2Sens BE Sensitivity to Mod source 2 ±99 Dca3Levei BF Programmed DCA 3 volume 0-99 Dca3Mods CO DCA 3 Mod. Source 0-15 Dca3ModlSens Cl Sensitivity to Mod source 1 ±99 Dca3Mod2Sens C2 Sensitivity to Mod source 2 ±99 I-IardSync2 C3 32 Spectrum'“ Bass II Appendix C System Exclusive Variable Name Offset Descriptio

NOTA: Si el problema del ruido continua consulte con su proveedor autorizado Peavey, a la fábrica o a un técnico de servicios calificados. EL INTERRUPTOR DE TIERRA NO ES FUNCIONAL EN LOS MODE LOS 220/240 VOLTS. POWER SWITCH (15) (Interruptor de Poder) Presione el interruptor a la posición de encendido (ON). La luz roja del piloto (indicacor) se encenderá indicando que la unidad esta recibiendo el poder. 1 SOW RMS POWER PnEAMP FOOT 2* 5V RMS AMP 'fi OUT SWITCH 4 OHM PEAVEY EUCTWMC5CCIV MERIR

All strings must be stretched upon installation. After your first tuning, carefully pull each string away from the fretboard, stretching it gently (too much force will break thinner strings). Then, retune your guitar. Peavey recommends that you replace strings in the same gauges to maintain proper neck and/or tremolo tension. If you wish to change strings with different gauges, Peavey recommends that you enlist the services of a qualified technician to make the required truss rod and/or tremol

En este modo el INTERRUPTOR 1 (30) selecciona entre los canales Limpio y Lider. El LED DEL CANAL (31) se iluminara cuando el canal Lider este activo. El INTERRUPTOR 2 (33) cambia entre dos efectos y sus ajustes respectivos. Este interruptor puede ser usado como interruptor de encendido y apagado si una de las posiciones no tiene efectos activos. Para usar el LED DE MODULACION (32) como indicador de estatus, la posicion apagado (off) o posicion baja deber ser hecha con el indicador de LED apagado

If the fuse should fail. IT MUST BE REPLACED WITH THE SAME TYPE AND VALUE IN ORDER TO AVOID DAMAGE TO THE EQUIPMENT AND TO PREVENT VOIDING THE WARRANTY. If the amp repeatedly blows fuses, it should be taken to a qualified service center for repair. WARNING: THE FUSE SHOULD ONLY BE REPLACED WHEN THE POWER CORD HAS BEEN DISCONNECTED FROM ITS POWER SOURCE. GROUND SWITCH (3) Three-position rocker-type switch which, in most applications, should be operated in its center or zero position. There may