Each unit consists of a ceramic fiber heater mounted in a 2.5 inch (64 mm) deep sheet metal case that provides thermal insulation. The case includes post terminals for electrical connections and provides a mounting system that can be used with virtually any flat ceramic fiber unit, whether it is a stock, standard or a custom size. Since any of the flat unit heating element configurations can be used—exposed sinuated, embedded coil or foil elements— watt density and temperature capabilities can b

The control mode options include factory selected combinations of ON/ OFF, time proportioning, PI using manual reset and full PID. Input for the Series 160 is a relative humidity/ temperature sensor. Features include mechanical relay outputs, remote setpot, optional remote digital displays, and various cable lengths to accommodate remote sensor location. The Series 160 is also available as a RH/Temperature signal conditioner only, that can be interfaced to other Watlow controls. Specifications

IS SEC CYCLE TIME C = TIME PROPORTIONING 15°F BAND. 9 SEC CYCLE TIME D = TIME PROPORTIONING _25“F BAND. 5 SEC. CYCLE TIME OUTPUT LD MD KO A = 35A SPST 0 = 60A SPST G = 25A SPST B = 35A 2PST E = 60A 2PST H = 25A 2PST C = 35A 3PST F = 60A 3PST J = 25A 3PST UNE VOLTAGE 115 VAC 230VÄCT CONNECTIONS I - QUICK CONNECTS 2 = BARRIER STRIP SEÎPOT ASSEMBLY ~ i - INTFGftAL 2 = REMOTE ♦ SENSOR RANGE NO 600 = 50 TO 500"F 10 TO 260°C __TYPE J TC 601 = 50 TO IOOO”F 10 TO 538“C TYPE J T£_ 6

The maximum recommended surface temperature of the heater is based on the rating of the ceramic fiber heater module. This can vary from 1095°C (2000°F) at lower watt densities, to higher watt densities at reduced surface temperatures. Note that maximum wattages cannot be achieved at the maximum Width: inches (mm) 2 (51) 30 (760) Any Length: inches (mm) 6 (152) 52 (1320) Any Note: Units will be 1.4 inch (6 mm) wider than the nominal size of the HHeeaatteerr DDiimmeennssiioonnss MMiinn.. MMaaxx..

Other voltages are available. Terminals: Non-standard locations are also available. Please specify. Standard Dimensions: ±Xe inch (0.0625 mm) Typical Peak Energy Wavelength: 3-3.5 microns Specifications Heater Dimensions Min. Max. Increments Width: inches (mm) Length: inches (mm) Area: in (cm ) 1 (25.4) 6 (152.4) 6 (38.7) 36 (914.4) 70 (1778) 864 (5574.2) 1 (25.4) any any Note: Less than maximum length X width may exceed maximum area. How to Order To order your stock RAYMAX heater, spe

ULTRAMIC 600 heaters are constructed of aluminum nitride (AIN) and incorporate a thermally matched proprietary heating element that provides maximum performance in challenging applications. AIN is especially suitable for applications requiring a clean, non-contaminating heat source. Additionally, the excellent geometric stability ensures consistent part-to-part thermal contact during heating cycles. Watlow AIN heaters can operate up to 600°C with an ultrafast ramp rate of up to 150°C per second

The opposite end is sealed to resist contamination. Standard 305 mm (12 in.) flexible lead wires are crimp connected to the terminal pin and have silicone impregnated fiberglass oversleeves. With its round cross-section geometry, the double-ended WATROD is highly adaptable for bending – especially when bending is performed in the field. Both single- and double-ended WATRODs share many construction features that deliver long life—the resistance wire is centered in the heater sheath and electrical

With heat-up and cool down capabilities of 40 to 50 seconds, the quartz heater is ideal for use in operations where frequent line stoppages are anticipated or immediate heat-up and cool-down is necessary. Custom sizes are available up to 27 inches wide in three inch increments and 70 inches long. Applications • Heating plastic films • Ink drying • Coating curing • Fusing powder coating • Activating adhesives Features and Benefits Quartz tubes and reflectors are easy to replace • Less do

BOX 5580, Winona, MN 55987-5580, Phone: 507/454-5300, Fax: 507/452-4507 0600-0008-0000 Rev D $10.00 November 1995 Made in the U.S.A. Supersedes without change: W733-XSMN Rev D00 Contents Contents This manual is a supplement to the Series 733/734 Program Manual. It is for configuring, servicing and calibrating your control. Use this manual in conjunction with the Series 733/734 Program Manual and Data Communications manual. PageItem Chapter 1 3 Install and Wire the Series 733/734 3 Dimensions 3 P

The RELIALINE™ 170 provides precisely controlled heat distribution and is automatically self regulating to deliver excellent temperature uniformity. It offers a custom thermal solution within a stock product delivery timeframe. Watlow’s newest heating system technology is constructed and designed for adaptability, which is perfect for quick prototyping. This patent-pending technology allows Watlow to configure a product to specific dimensions and three-dimensional installation drawings are provi