Preamplifier Gain The SmartMixer has a substantial gain range, allowing it to accept a wide variety of microphones. However, if in some instances higher-output microphones are used for close talking, it may be necessary to reduce the preamplifier gain. This can be done by changing switch settings inside the unit. With the unit unplugged from its AC source, remove the two screws on each side of the unit and carefully lift off the top cover. Locate the internal switches designated on the circuit b

It is designed for quality sound reinforcement, professional recording, television and other demanding sound pickup applications. The ES933PMML is furnished with a vinyl-coated steel hanger that allows it to be adjusted for correct positioning. An included foam windscreen effectively reduces noise from wind or ventilation air currents. The ES933PMML is equipped with UniGuard® RFI-shielding technology, which offers outstanding rejection of radio frequency interference (RFI). The microphone is RoH

Note: If the cable jacket’s outer diameter is less than 7/32" (0.21", 5.3 mm), wrap the jacket with electrical tape to build up its diameter before folding back the braid over the jacket (C2). Trim the shield wires to 9/16" (15 mm). RG8:When using RG8-type cable, more jacket material needs to be removed and partially replaced with shrink tubing. When installing the tubing, heat the tubing and cable only enough to shrink the tubing. Allow the cable to cool fully before manipulating it further. Th

CAUTION! The circuits and wiring inside the antennas are adjusted for optimum performance. Do not attempt to alter circuitry or wiring to affect output. To do so will void the warranty and may cause improper operation or system degradation. Introduction Audio-Technica ATW-A62P and ATW-A72P powered dipole antennas provide effective and reliable signal pickup for UHF wireless systems. Supplied in pairs, these antennas are intended to improve performance of diversity wireless receiving systems with

3. Gently move the tone arm so the stylus is over the point on the record where play is desired to begin. 4. Press the Lift button again to gently lower the tone arm and play record. (Out) Figure 6 (In) (Out) (In) Replacing the Stylus While holding the head of the tone arm, rotate the front of the stylus assembly in a forward and down motion to remove it (Fig. 8). (As you remove the old assembly, note its position and “feel,” to aid in properly installing the new one.) Install the new stylus ass

Internal adjustments are for qualified professionals only. Refer all servicing to qualified service personnel. AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Warning: To prevent fire or shock hazard, do not expose this appliance to rain or moisture. Attention: Pour prevenir feu ou choc electrique, ne pas expose l’appareil a la pluie ou a l’humidite. Cuidado: Para evitar descargas electricas o el peligro de incendio, no exponga este aparato a la lluvia o h

CAUTION AVIS RISK OF ELECTRIC SHOCK RISQUE DE CHOC ELECTRIQUE DO NOT OPEN NE PAS OUVRIR To prevent electric shock, do not remove the cover. There are no user-serviceable parts inside. Refer all servicing to qualified service personnel. Warning: This apparatus must be grounded. This product is a safety class 1 product. There must be an uninterruptible safety earth ground from the main power source to the product’s AC input. Whenever it is likely that the protection has been impaired, disconnect t

5). 3. Seleccione el tamano del disco: 12" o 7" (Fig. 6). 4. Seleccione la velocidad: 33 1/3 RPM o 45 RPM (Fig. 7). 5. Inicio: pulse suavemente el boton START (INICIAR) (Fig. 8a). El tocadiscos comenzara a girar y el brazo de lectura se colocara automaticamente en el surco inicial. Cuando finalice la reproduccion del disco, el brazo de lectura volvera Figura 5 Adaptador de 45 RPM automaticamente al soporte y el tocadiscos se detendra. Unidad de la aguja Aguja Protector de aguja 6. Parada: para d

Si el enchufe que se incluye no encaja en su toma de corriente, solicite a un electricista que sustituya la toma de corriente obsoleta. 10. Proteja los cables electricos de pisadas o presiones, especialmente en los enchufes, las carcasas de los dispositivos y en los puntos de salida de los aparatos. 11. Utilice unicamente los complementos/accesorios especificados por el fabricante. 12. Utilicelo solamente con carro, estante, tripode, soporte o mesa especificados por el fabricante, o vendidos jun

7 Audacity Installing Audacity software (for Mac OSX and above) ………………...........................14 Setting up your Mac (OSX and above) to work with AT-LP2D-USB Turntable.............15 Additional Macintosh audio settings ……………………………………............................17 Installing Audacity software (for PC) ……………………………………............................18 Setting up your PC to work with Audacity ……………………………….........................19 Recording albums with Audacity …………………………………………......................