(Certains etats ne permettent pas la limitation de la garantie implicite, il est donc possible que la limitation cidessus ne s’applique pas a vous.) Aucun recouvrement, quel qu’il soit, ne sera d’un montant superieur au prix du produit vendu. Toute modification des dispositifs de securite du produit annulera la presente Garantie. Vous assumez tout risque et toute responsabilite resultant de la perte, de l’endommagement ou du prejudice que vous et votre propriete et/ou d’autres et leur propriete

Realice siempre el mantenimiento y las reparaciones con la unidad fria. Desconecte el cable de la bujia de encendido para cerciorarse de que la unidad no arrancara. NOTA: El mantenimiento, la sustitucion o arreglo dedispositivos para el control de emisiones ysistemas pueden ser hechos por cualquierestablecimiento de reparacion, persona oproveedor de servicio autorizado que arreglemotores para uso fuera de la carretera. A fin de garantizar el maximo desempeno del motor, puede ser necesario inspec

SIMBOLO SIGNIFICADO ALERTA DE SEGURIDAD: Indica peligro, advertencia o precaucion. Debe prestar atencion para evitar sufrir graves lesiones personales. Puede ser utilizadojunto con otros simbolos o figuras. NOTA: Le offece informacion o instrucciones que son esenciales l}ara la ol}eracion o mantenimiento del equil}o. Lea el manual del operador y siga todas las advertencias e instrucciones de seguridad. De no hacerlo, el operador y/o los espectadores pueden sufrir graves lesiones. SI TIENE PREGUN

Fingers may become trapped between split wood. 1. To remove partially split wood from wedge, move control handle to REVERSE position until wedge is fully retracted to allow split wood portion to contact the log dislodger. 2. Once removed from wedge with log dislodger, split wood from opposite end or in another location. Vertical Position 1. Pull the horizontal beam lock out to release the beam and pivot the beam to the vertical position. 2. To lock the beam in the vertical position, pull out on

4. Water or dirt in fuel system. 5. Dirty air cleaner. 6. Carburetor out of adjustment. 1. Connect and tighten spark plug wire. 2. Move choke lever to OFF position. 3. Clean fuel line; fill tank with clean, fresh gasoline. 4. Drain fuel tank. Refill with fresh fuel. 5. Clean or replace air cleaner. 6. See authorized service dealer. Too much vibration 1. Loose parts or damaged impeller. 1. See authorized service dealer. Engine overheats 1. Engine oil level low. 2. Dirty air cleaner. 3. Carburet

Nozzle Height Adjustment The nozzle can be adjusted to any five positions, ranging from 5/8” to 4 1/8” ground clearance. The nozzle height has to be adjusted according to the conditions. Move the height adjustment levers forward or backward to adjust the nozzle upwards or downwards. See Figure 8. NOTE: In general, raise the nozzle height to vacuum a thick layer of leaves or to operate with the blower chute and lower the nozzle height for smoother surfaces. Figure 8 SECTION 5: MAINTAINING YOUR CH

Por favor cuando llame tenga a la vista el numero de modelo y el numero de serie de su unidad. Consulte la seccion anterior para obtener esta informacion. Se le solicitara que ingrese el numero de serie para poder procesar su llamada. Si desea mas informacion sobre la maquina visite nuestro sitio web en 19 SECCION 1: MEDIDAS IMPORTANTES DE SEGURIDAD ADVERTENCIA: La presencia de este simbolo indica que se trata de instrucciones importantes de seguridad que debe respetar para evitar poner en riesg

24645-9 Important: Read Safety Rules and Instructions Carefully vaRD-MaN 8 H.P. DELUXE LOG SPLITTER PRINTED IN U.S.A. _/ FORM No. 770-8316 LIMITED WARRANTY For one year from the date of original retail purchase,YARD MAN COMPANY will either repair of replace, at its option, free of charge, F.O.B. factory or authorized service firm, any part or parts found to be defective in material or workmanship. Transportation charges under this warranty must be paid by the purchaser unless return is

Throttle Lever On/Off Switch Handle Connectors Primer Starter Handle Front Handle Cultivator Choke Lever Edger Wheel Edger Blade Tines 7 • Remove the oil plug/dipstick from the crankcase and pour the entire bottle of oil into the oil fill hole. See Figure 3. • Wipe up any oil that may have spilled and reinstall the oil fill plug/dipstick. Figure 3 Gas Fill-Up Old fuel is the primary reason for the unit not running properly. Be sure to use fresh, clean, and unleaded gasoline. Use fresh fuel (less

Read and follow instructions carefully. 9 Service air cleaner every 25 hours under normal conditions. Clean every few hours under extremely dusty conditions. Poor engine performance and flooding usually indicates that the air cleaner should be serviced. To service the air cleaner, refer to the separate engine manual packed with your unit. The spark plug should be cleaned and the gap reset once a season. Spark plug replacement is recommended at the start of each season; check engine manual for