WIRING DIAGRAM INSTALLATION This wall switch can be used for either single pole or multiswitch installation. A multiswitch installation with an electronic wall switch differs from conventional installation. Read wiring instructions carefully. Use guidelines applicable to your installation. Apply the following steps for all installations. Note: The black wall switch wires have no polarity. You can use any of them. 1. Interrupt power at circuit breaker to avoid electric shock. 2. Take out and disc

Esta garantia no cubre los costos de desinstalacion y reinstalacion. Esta garantia no sera valida si se demuestra que el defecto o el mal funcionamiento se deben a un dano que ocurrio cuando el producto estaba en posesion del consumidor. La unica responsabilidad de AUBE sera la de reparar o reemplazar el producto de acuerdo con los terminos aqui establecidos. AUBE NO SERARESPONSABLE DE NINGUNA PERDIDA NI DE NINGUN DANO DE NINGUN TIPO, INCLUIDOS LOS DANOS IMPREVISTOS O DERIVADOS QUE RESULTEN, DIR

• Installation • Cut power at the circuit breaker to avoid electric shock. • Remove the existing switch. (For a 3-way installation, identify and label the wire that is connected to the “common” screw.) • Install the new switch (refer to the appropriate section below). • Apply power at the circuit breaker. NOTE A: The white wire is not the neutral wire but the wire going to the load. SINGLE-POLE INSTALLATION 120 VAC Neutral Line See NOTE A 120 VAC Line Neutral Connect wires "2" and "C" of TI034-3

• In continuous mode, the fan runs continuously and the symbol is displayed. NOTE: If the “smart fan” feature is enabled, the fan will run only when heating or cooling will be activated during unoccupied mode. 6. Temperature Setting 6.1 Display Appears when the temperature setpoint is displayed Indoor temperature Heating is On Cooling is On System operating mode Auxiliary heating is On Temperature adjustment mode (appears when the Fan operating mode controller is in automatic (appears when the f

• Description This user guide covers the following thermostat models: • TH131 A/F/AF • TH133 A/F/AF The TH131 model is designed for residential applications, whereas the TH133 model is designed for public areas as its controls are hidden and thus protected against unauthorized access. Both models can be configured for the following applications: Type Application A Controls the ambient (room) temperature F Controls the floor temperature AF Controls the ambient temperature and limits the floor tem

DAY/HOUR/MIN— Set the day and clock settings. .. PGM—Program the schedule (programs). .. MODE—Select the operating mode. RETURN—To exit a function. .. To configure temperature setpoints: Comfort, Economy and Vacation. .. Adjust the floor temperature limit (AF only). .. —Increase and decrease temperature. .. —Indicates the number of the current program when Automatic mode is enabled. .. Current operating mode (auto / manual ). In Auto mode, the program’s associated setpoint icon is also displayed

Heating indicator Temperature selection dial On/Off switch Pilot wire indicator (Europe only) TH131-15S TH133-15S Front View Rear View NOTE: Even if the following illustrations show the TH131 model only, they can also apply to the TH133 model. • Description This user guide covers the following thermostat models: • TH131-15S A/F/AF • TH133-15S A/F/AF The TH131-15S model is designed for residential applications, whereas the TH133 model is designed for public areas as its controls are hidden and th

Aube's sole responsibility shall be to repair or replace the product within the terms stated above. AUBE SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some regions do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you. THIS WARRANTY IS THE ONLY EX

. . . . . . . . SUMMARY TO SET TIME AND DAY Press DAY, HOUR and MIN keys to adjust the time and day. TO MODIFY HEATING AND COOLING PROGRAMS • Set the function switch to HEAT position for heating programs and to COOL for cooling programs. • Use PROG key to select the program to be modified. • Use HOUR and MIN keys to set the time and or button to select the temperature setting. OPERATING MODES AUTO: executes the programs. or button shows the temperature setting. MAN: bypasses the programmin

The TH113 and TH116 are equipped with a remote input which allows connection of an optional telephone controller (CT240) or any other remote control system. When a command signal is received through this input, the thermostat automatically lowers its setpoint by 3.5°C. The LED lights up to indicate the signal’s presence (except for GA and GB models). Bypass (not available for GA and GB power base): The TEST button can be used to bypass the signal for a 2-hour period. The LED goes off to indicate