IF YOU ARE UNCLEAR AS TO WHAT YOU ARE INSTRUCTED TO DO OR BELIEVE THAT YOU DO NOT UNDERSTAND THE INSTRUCTIONS SO AS TO PROPERLY AND SAFELY COMPLETE THE INSTALLATION YOU SHOULD CONSULT A TECHNICIAN WHO DOES HAVE THIS KNOWLEDGE AND UNDERSTANDING. FAILURE TO FOLLOW THESE INSTRUCTIONS CAREFULLY AND TO INSTALL THE INTERFACE AS DESCRIBED COULD CAUSE HARM TO THE VEHICLE OR TO SAFETY SYSTEMS ON THE VEHICLE. INTERFERENCE WITH CERTAIN SAFETY SYSTEMS COULD CAUSE HARM TO PERSONS AS WELL. IF YOU HAVE ANY QUE

2. Cycle the key by turning the ignition on then back off, then back on again to test the radio for proper operation. 3. If the subwoofer or front door speakers are too loud you can adjust the output by following the steps below: A. Locate the end of the MITO-01 with the 14 way Molex connector. B. There are 2 potentiometers next to the Molex connector, the one closest to the Molex connector is the subwoofer control and the other one is the front door speaker control. 1-800-221-0932 ©Copyright 20

............................ .2 -Stacked ISO Mount Units Provision .......................... 2 Final Assembly ...........................................3 *Note: Refer also to the instructions included with the aftermarket radio. 95-8150 DASH DISASSEMBLY LEXUS ES SERIES 1992-1996 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the plastic trim piece below the factory radio and remove (2) Phillips screws exposed underneath. (Figure A

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2 Kit Assembly DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . 3,4 ISO Radio Provision with Pocket .......................5,6 Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 7,8 Two ISO Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9,10 Final Assembly ......................................11 99-8151 DASH DISASSEMBLY DASH DISASSEMBLY LEXUS IS 300 2001-2

2 - ISO Din Head Unit provision with Pocket...................... .3 Final Assembly ...........................................4 *Note: Refer also to the instructions included with the aftermarket radio. 99-7324 DASH DISASSEMBLY KIA OPTIMA 2006.5-2010 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the panel surrounding the radio including the a/c vents and climate controls. (Figure A) 3 Remove (4) Phillips screws securing radio. Un

Please refer to GMOS-100i for 20 pin connector instructions *Read Important Warning On Page 1 Before Attempting Any Installation* APPLICATIONS GMLAN29-100 BUICK Enclave 2007-10 Lucerne 2006-10 CADILLAC Escalade 2007-10 DTS 2006-10 SRX 2007-09 CHEVROLET Avalanche 2007-10 Equinox 2007-09 Express 2008-10 Impala 2006-2010 Monte Carlo 2006-2007 Silverado (new body) 2007-10 Suburban 2007-09 Tahoe 2007-09 Traverse 2009 GMC Acadia 2007-10 Savanna 2008-10 Sierra (New body) 2007-10 Yukon 2007-10 HUMMER H2

Reach under the driver's side dash and unclip the temperature control cable. Using Metra's 86-5618, pull the factory radio/climate control panel from the dash. Disconnect the switch power harness, antenna plug, radio/speaker power harnesses and vacuum hose harness. 2 CONTROL PANEL) Turn the integrated control panel over and disconnect the vent control harness ("A"), fan speed control harness ("B"), and defroster harness ("C"). Unclip the main switch harness from the side of the factory unit.

THE WORLD’S BEST KITS.™ a 1-800-221-0932 Q © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION 95-2 no TABLE OF CONTENTS Dash Disassembly 1BB7-2001 Cadillac Catera ............................. 1 1BB6-1BBB Cadillac Devllle (Column Shift Only) ............. 1 Kit Preparation 1BB7-2001 Cadillac Catera.............................2 1BB6-1BBB Cadillac Deville (Column Shift Only) ............. 2 Kit Assembly 1BB7-2001 Cadillac Catera / 1BB6-1BBB Cadillac Deville ( Column Shift Ony) DDIN Hea

Desconecte y retire el radio. Pase a la página de montaje del kit. DODGE DAKOTA 2001-2004 DURANGO 2001-2003 1 Desconecte el terminal negativo de la batería, a fin de evitar un cortocircuito accidental. 2 Retire (3) tornillos de cabeza Torx T-20 del borde inferior del panel que se encuentra debajo de la columna de la dirección y quite a presión para retirar el panel. 3 Retire (2) tornillos Phillips del panel de grupo de instrumentos que se encuentra arriba de los indicadores. 4 Retire (3) to

(únicamente Concorde). 3 Desenganche el panel de terminación de la palanca de velocidades y deslice el panel de terminación hacia la parte trasera del vehículo. 4 Desenganche el panel de terminación del tablero y desconecte el cable del panel de terminación. 5 Retire (4) tornillos de cabeza Phillips que v sujetan el radio. Desconecte y retire el radio. Pase a la página de montaje del kit. CHRYSLER PT CRUISER 2DD1-2DD5 1 Desconecte el terminal negativo de la batería, a fin de evitar un corto