canal 2 queda ignorada. Modo de salida .. .................................................................................................................................................................................................................................................... del canal 2 a la salida del canal 2. .. .............................................................................................................................................................................

Nota: Los conectores hembra de salida de los modelos europeos se entregan con tapones de seguridad instalados para evitar que se inserten enchufes europeos. Con los modelos europeos, deben usarse las entradas laterales para estos conectores. Conectores hembra de salida: Un par por canal, aceptan conectores banana o cable pelado. Nota: Los conectores hembra de salida de los modelos europeos se entregan con tapones de seguridad instalados para evitar que se inserten enchufes europeos. Con los mode

Conectar el altavoz como se muestra a. Conecte un altavoz a cada salida de canal usando Speakon®, conectores banana o cable pelado Siga estos pasos rapidos para configurar el amplificador en modo SINTETIZADOR SUBARMONICO: 1. Pulse el boton “Set/Enter” y vera que parpadea la palabra “Preset” 2. Vuelva a pulsar el boton “Set/Enter” para introducir la lista de configuraciones en el amplificador 3. Pulse el boton “Next/Down” o “PREV/UP” hasta que aparezca en la pantalla “SUBSYNTH” 4. Pulse el boton

El amplificador esta configurado para el modo estereo con todos los procesamientos desactivados. 1. Conecte la fuente de senal Left/Right (izquierda/derecha) al canal 1 (CH1) y al canal 2 (CH2) usando los conectores XLR 2. Conecte un altavoz a cada salida de canal usando Speakon®, conectores banana o cable pelado Preajuste de fabrica num. 2: BRIDGE (PUENTE) Al poner el amplificador en modo BRIDGE (bridge-mono), entrega la potencia de los dos canales del amplificador en una unica carga de 8 o 4 o

....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

wide n Multiple boiler systems provide increased turndown and even smoother, more efficient system operation n 4 boilers w/4:1 Turndown =16:1 total system turndown 40 100 140 VW/ VB-500 500,000 421,500 1,268 507 362 56 30 37.5 30 450 VW/ VB-750 750,000 633,750 1,901 761 543 62 30 37.5 30 575 VW/ VB-1000 1,000,000 845,000 2,535 1,014 724 71 30 37.5 30 750 With Ac-U-Temp, A. O. Smith makes it as easy as possible to install a complete packaged hot water supply system, combining 88% efficient VF Ser

NOTE: Do not use a push type ratchet screwdriver. 1. Strip 7/16 in. of insulation from the wire end. 2. Wrap the wire at least three-fourths of the distance around the screw as shown. 3. Using a standard, flat-headed screwdriver, tighten the screw until the wire is snugly in contact with the screw and contact plate. 4. Tighten the screw an additional one-half turn. Fig. 4—Typical hookup for L8151A in a single zone system. L1 (HOT) L2 1 2 3 1 2 3 POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOA

Because the and post purge operating states and at lower speeds sensing tubes are T fitted together it is not con- during all other operating states. High blower prover clusive which BPS is at fault. IE: a leaking diaswitch contacts must close during the pre and post phragm on the Low BPS could prevent the High purge states ONLY and open during all other BPS from closing its contacts. Therefore - operating states. replace both the High and Low BPS. OR Normally Open Low Blower Prover pressure swi

Ball Valve...............................................................191935 2......Tank/Pump Kit (LW Models Only - Not Shown)......210625 3......Hex Reducing Bushing (LB Only).......................... 91940-8 4......Flush Bushing (LB Only).......................................192163-2 5...... Relief Valve (LW Model)........................................ 98883-3 Relief Valve (LB Model).........................................210451-2 6......Strap, Cable (not shown).............