Installation could be the problem: Your hood was designed to SMOKE/STEAM/ meet specific ducting requirements. If your duct length exceeds ODORS ADEQUATELY the manufacturer's requirements, hood performance will suffer. Air-flow will also be reduced if the house duct work is too small or there are too many elbows in the system. Contact your installer or builder. 2. Obstruction in duct work could be the problem: Make sure nothing is blocking the vent (bird nests or kinks in the duct work). 3. Dampe

C. Si vous faites un trou ou une ouverture dans un mur ou un plafond, n’endommagez pas les fils electriques et les autres installations cachees de service public. D. Vous devez toujours alimenter les ventilateurs dans les conduits en air en provenance de l’exterieur. AVERTISSEMENT : POUR REDUIRE LE RISQUE D’INCENDIE, N’UTILISEZ QUE DES CONDUITS EN METAL. • N’essayez jamais de remplacer ou de reparer un element de votre hotte si le present manuel ne le recommande pas expressement. Tout autre entr

Do not use abrasives or oven cleaners. Rinse, shake and let them dry before replacing. They may also be cleaned in an automatic dishwasher. To remove: Grasp the baffle knobs and pull them up, forward and out. Grasp the drip tray and carefully lift it up and out of the hood track. To replace the drip trays: 1. Place and seat the drip tray into the hood track. 2. Slide them left or right until all trays are side-by-side in place in the track. To replace the baffles: 1. Hold the baffle at the botto

49-80596 04-10 GE Informacion para el consumidor Campana de acero inoxidable Contenidos Servicios para el consumidor Instrucciones de seguridad. 26 Garantia. 32 Numero de modelo y de serie . 25 Numeros telefonicos importantes. 31 Solucionador de problemas . 30 Controles y caracteristicas. 27 Cuidado y limpieza Bandeja colectora. 29 Bombillas de luz . 29 Filtros de carbon . 28 Filtro de grasa metalico . 28 Superficies de campana. 28 Antes de usar su campana de acero inoxidable Lea este manual con

To replace the baffles: 1. Hold the baffle at the bottom by one of the knobs . 2. Place the other end of the baffle against the inside front of the hood. 3. Slide it up and push the bottom end back until it firmly seats into place. Drip Tray Drip Tray Track Drip Tray Replacement Baffle Baffle Replacement Care and Cleaning Professional Range Hood Stainless steel Do not use a steel wool pad; it will scratch the surface. To clean the stainless steel surface, use warm sudsy water, a stainless steel

And you can call any time. GE Answer Center® service is open 24 hours a day, 7 days a week. OR Visit our Website at: A GE consumer service professional will provide expert repair service, scheduled at a time that’s convenient for you. Many GE Consumer Service company-operated locations offer you service today or tomorrow, or at your convenience (7:00 a.m. to 7:00 p.m. weekdays, 9:00 a.m. to 2:00 p.m. Saturdays). Our factory-trained technicians know your appliance inside and out—so most repairs c

N’utilisez cet appareil que de la maniere prevue par le fabricant. Si vous avez des questions, appelez le fabricant. B. Avant de reparer ou de nettoyer votre appareil, debranchez le courant au niveau du panneau de service et verrouillez les mecanismes de debranchement de service pour eviter tout branchement accidentel au courant. Si vous ne pouvez pas verrouiller les mecanismes de debranchement de service, attachez soigneusement un avertissement bien visible, comme une etiquette, au panneau de s

Check to be sure that oven supports above the Warming Drawer location do not obstruct the required interior 23-1/2" depth and 9-1/4"height. 10-1/2" t 9" ^-2x4 or 2x2- Runners or Solid Bottom Including Handle Install '2x4 or 2x2 Anti-Tip Block Against Rear Cabinet Wall 9" From Floor to Bottom of Block Undercounter Installation (in inches) Note: When installing warming drawer with a cooktop, allow a 2" minimum from cooktop burner box bottom to top of cut-out. Important Installation Note:

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. DO NOT USE AN EXTENSION CORD. Remove Packaging and Parts Installation Below a Countertop • Place carton on a flat surface. • Open one end of the carton and lift off the top piece. • Lift the warmer up and out of the carton. • Place the drawer on top of the shipping carton to protect the drawer front and the finished flooring. Electrical Outlet Against Rear Cabinet Wall 9" From Floor Flush With Side of Ca

– There is no way to level the drawer once it has been installed. Be sure supports are level. • The entire weight of the drawer is supported by the runners or solid floor and must be capable of supporting 150 lbs. 9" 2x4 or 2x2 Runners or Solid Bottom Install 2x4 or 2x2 Anti-Tip Block Against RearCabinet Wall 9" From Floor to Bottom of Block Step 2 Install Warming Drawer • Slide left corner of the drawer into the opening. • Push power cord into the hole leading to the outlet location. Thread the