For concrete and rock mounting material, allow for proper ventilation before mounting the TPS-6X-DSW. There are two Trim Ring Mount Kits. The TMK-6X-DSW is a pre-construction accessory. Pre-construction refers to framed walls prior to hanging drywall. This accessory must be used with either the Pre-Construction Mount Kit (PMK-6X-DSW) or Wall Mount Back Box (BB-6X-DSW). The WMKT-6X-DSW is a post-construction kit. Post-construction refers to framed walls with drywall hung. This accessory is design

• If mounting into the BB-6X-DSW, bend the flanges back as far as they can go. 6. Use four standard drywall screws (length should not exceed drywall thickness by more than 1/2 inch) to secure the mud ring plate to the rest of the assembly. The screws pass through the clearance holes in the PMK-6X-DSW (or BB-6X-DSW) and are secured in the extruded holes of the adjustment plates. 7. Verify that the mud ring plate is level. NOTE: Do not overtighten screws. Doing so may over-dimple or rip the mud ri

................................................................................17 How the Program Works...........................................................................................18 How to Create the Program .......................................................................................18 Reserved Join Numbers.............................................................................................21 Problem Solving .....................................................

©2007 Crestron Electronics, Inc. Contents Isys® G-Series Touchpanel Interface: TPS-GA-TPI 1 Introduction...............................................................................................................................1 Features and Functions................................................................................................1 Internal Block Diagram...............................................................................................3 Specifications..............

A reduction in image size will save a considerable amount of memory space for your project. In VT Pro-e, the Compress checkbox permits the image to be compressed when compiling. The 16 Bits checkbox converts a 24-bit or 32-bit image to 16 bits. This conversion to a 16-bit image may cause the loss of some subtle shading. To compensate for this, use the dithering to simulate the original shading. Various dithering types are available. Refer to the following illustrations. VT Pro-e “Page Properties

The Exit and Run Program button verifies that all of the setup information has been saved to the EEPROM and displays the main page that has been programmed into your system. The remaining buttons on the MAIN MENU open other menus which are discussed in subsequent paragraphs. MAIN MENU Calibration Menu CALIBRATION MENU Touch Perform Calibration. The message “Touch Upper Left” appears centered on the panel with a cross hair in the upper left corner. Touch the center of the cross hair in the corner

Multi-Mode Objects Multi-mode objects offer high- performance programming! The single most-advanced VT Pro-e high-performance programming technique involving the TPS-12B/W, TPS-15B/W & TPS-17B/W is the concept of multi-mode objects. A multi-mode object (i.e. button, legend, etc.) is an object drawn on a VT Pro-e page that can have one or more active and inactive visible settings (modes). For examples, refer to and search for multi-mode object examples. This file contains the VT Pro-e touchpanel

Windows®, Windows® XP and Windows® Vista are registered trademarks of Microsoft Corporation in the United States and other countries. ©2009 Crestron Electronics, Inc. Contents Isys i/O™ 8.4” TableTop WiFi Touchpanel: TPMC-8T 1 Introduction...............................................................................................................................1 Features and Functions................................................................................................1 Specificatio

WARNING: Charge the touchpanel in a well ventilated area away from sparks and open flame. Do not use the touchpanel near heat sources such as radiators, heat registers, stoves or other apparatus. CAUTION: Avoid accidental shorting of the electrical contacts to prevent possible damage to the touchpanel. NOTE: Docking station contacts can be cleaned with electrical contact cleaner (not included). Follow directions that come with the cleaner. Further Inquiries If you cannot locate specific informat

3.63 in(9.22 cm) 2.25 in(5.72 cm) 6.25 in(15.88 cm) FROM (included) AC POWER PACK WARNING: To avoid possible physical harm, damage to the TPMC-4XG-DS or touchpanel, use only the included power pack (100-240 VAC, 50/60 Hz) when charging. WARNING: Charge the touchpanel in a well ventilated area away from sparks and open flame. Do not use the touchpanel near heat sources such as radiators, heat registers, stoves or other apparatus. CAUTION: Avoid accidental shorting of the electrical contacts to pr