Insert 4 AAA bateries observing the polarity ashown. Inst alling the bateries incorectly wil preventhe unit from operating or may damage the unit. bel3t .c Rlipe,t umrna ktihneg Bsautrtee rity loCcokvse irn btoy psllaidcineg. it up on the radio. Replace the 15 MMI ID DL LA AN ND D RRA AD DI IO O CCO OR RP PO OR RA AT TI IO ON N 590 0 P arr et ta Dr iv e Kansas City , MO 64120 Call 816.241 .850 0 visit us at ht tp://www .midlandr adio .com Not e: F eat ur es & Specifications ar e subject t o c ha

Designed for operation, this comp act p pieacek oafg el eisc tbroign inc epqeurfioprmeantc, component s. The circuitry is al solid-st ate and mounted on a rugged printed circuit board. Y our two-way radio is designed foreliable trouble-fre performance for years to come. Features - 22 GMRS/FRS Channel - Call - R-o SgAecarle nBr teF eupn ction T one - Silent Operation - Keyp - Paodw eLro cHkI/LO Setings - Auto Squelch - S - B-a Bteparetytae Lkryeo rwL /i fIMen diEcicxroateptonhrdoenre Jacks intecr

Establezca la hora usando >^ Ў o < y a continuacion presione SELECT. 12. Para CANAL presione el boton SELECT y a continuacion: 13. Sintonice el canal a la emision deseada usando ^o Ў. 14. Ajuste el volumen usando el boton VOLUME UP o VOLUME DOWN. 15. Para completar la configuracion, presione el boton SELECT. NOTA: Para restaurar los valores de fabrica de la radio, mantenga presionado el boton WEATHER / SNOOZE mientras pone en marcha la unidad. Para obtener el codigo S.A.M.E. en los Estados Unido

5 for important buttons and controls. 1. Place 4 AA batteries (not supplied) into the compartment on the underside of the radio. (Note:batteries are important because they provide emergency power for the radio in case of a power outage.) 2. Plug the AC adapter into a standard house outlet. Plug the other end of the adapter into the DC jack on the back of the radio. 3. Pull out the antenna and extend to its full length above the weather radio 4. Program the Weather Channel for Your Area( A). Turn

In this book… IN THIS BOOK…................................................................................................................................................. 2 WARNING NOTES ................................................................................................................................................. 3 FCC LICENSING INFORMATION............................................................................................................................ 3 SAFETY ....

The LED indicator will glow red indicating the battery is charging. 5. The rapid charger will fully charge the 1300 mAH NiMH battery in approximately 1.5 hours. The rapid charger will change to a green LED and switch to a trickle charge rate when a full charge is detected. The standard rate charger will charge at a constant rate (requires about 12 hours to fully charge a dead battery) and batteries should not be left in the charger longer than 15 hours. The LED of the standard rate charger does

.. If the status LED blinks red once every five seconds in standby, the battery needs charging. When a low battery condition is detected, the radio will automatically revert to low power when transmitting to help prolong the battery's life. If beeps are enabled, two short beeps will be heard before each transmission indicating the radio has automatically switched to low power mode. Sending a 2-tone/selective call or emergency call Your radio may have been programmed to send a 2-tone or selective

Midland Radio Corporation subscribes to the same safety standard for the use of its products. Proper operation of this radio will result in user exposure far below the Occupational Safety and Health Act (OSHA) and FCC limits. ? DO NOT transmit for more than 50% of total use time (50% duty cycle). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. ? This radio is NOT approved for use by the general population in an uncontrolled environment. Th

If you press the upper function button for less than two seconds the monitor mode will be activated while pressed and deactivated when released. For details, please see the “Monitoring the channel” section. .. If you press the upper function button for more than two seconds the monitor mode will latch on. To turn the monitor mode off, press and release the upper function button. For details, please see the “Monitoring the channel” section. [8] PTT (Push to talk) button. The PTT button must be pr

Use the and keys to select the desired bank. Press the A key to enable (e) or disable (D) the bank for scan. Press the and keys to select another bank or press B D C or to exit. Channel Scan Edit To add or remove a channel in the current bank from the scan list, press and hold the Scan programmable button for two seconds. Use the and keys to select the desired channel. Press the A key to enable (e) or disable (D) the channel in the scan list. Press the and C keys to D select another channel or p