Iniciar sesión:
Clasificado: Nombre ↑   Descargas   Tarifa   Tamaño ↑  

Chamberlain WKP5LM

Descargado: 3Tamaño del archivo: 128 kb    Fabricar: Chamberlain  
Categoría: Vídeo

Model WKP5LM can hold up to 5 PIN Numbers. Model WKP250LM can hold up to 250 PIN Numbers. Assembly Install 4 AA Alkaline batteries (not provided). (Lithium batteries recommended for colder environments.) Keypad will beep. Keypad will continuously beep indicating no Master PIN Number has been programmed. Proceed to Initial Setup. Keypad Initial Setup Step 1: On keypad press: Step 2: Enter 4 digit Master PIN Number. Example: 1234. ?? Multiple Keypads at Same Location Step 1: On secondary Keypad en

Chamberlain WKP250LM

Descargado: 0Tamaño del archivo: 128 kb    Fabricar: Chamberlain  
Categoría: Vídeo

The Master PIN Number cannot be deleted. Erasing PIN Numbers “BEEP” “BEEP” “BEEP” ?? 51?? ?? 2 Mount Keypad Step 1 Choose mounting location for Keypad. Remove the back panel and attach it to a solid surface or post. Mount the Keypad onto the back panel with screws. Tighten screws with Allen wrench. Step 2 It is recommended that Keypad be mounted to a Gooseneck post or non-metallic surface. If it is necessary to mount Keypad to a metal surface, use a non-metallic spacer to move the Keypad away fr

Chamberlain WIRELESS PORTABLE INDOOR/OUTDOOR INTERCOM NTD2

Descargado: 6Tamaño del archivo: 176 kb    Fabricar: Chamberlain  
Categoría: Teléfonos fijos

Mounting Tape Alcohol Wipe Intercom (2) Operation & Features Call Mode: In Call Mode the intercom may only be used to call the intercom network and will not be able to hear conversation from within the network. To put intercom into Call Mode place Dipswitch #1 to the UP position. Volume: To increase the intercom volume, place Dipswitch #4 to the UP position. Sensitivity: To increase sensitivity on the intercom set Dipswitch #3 to the UP position. NOTE: Dipswitch #2 is not used. Talk Button: To t

Chamberlain WIRELESS GATE ACCESS RGAIPI

Descargado: 0Tamaño del archivo: 839 kb    Fabricar: Chamberlain  
Categoría: Teléfonos fijos

The Wireless Gate Access Intercom is compatible with various Chamberlain Wireless Products and all Chamberlain Gate Operators. Indoor Intercom Rubber Pads Operation & Features Talk Button: Following the ringing of the doorbell by a guest, press and hold the Talk button to talk to the guest. Once the link to the Outdoor Intercom is made, any other intercoms in the network cannot hear the conversation. Select Button: During a conversation, the Select button can be pressed to open the gate. A beep

Chamberlain WIRELESS ALERT RWV400R

Descargado: 1Tamaño del archivo: 1 mb    Fabricar: Chamberlain  
Categoría: Vídeo

Mute: To temporarily mute Base Station, hold the Volume and Talk buttons down for three seconds. The Base Station will reactivate after one hour, or by pressing the Talk button. Remote Button: If there is an accessory device connected to the relay on the PIR Motion Sensor, it can be activated by pressing the Remote button within 30 seconds of the signal from the alert buzzer. On/Off: To turn Base Station OFF hold down the Volume button until a beep is heard and light goes out. To turn Base Stati

Chamberlain WIRELESS ALERT CWV1000

Descargado: 0Tamaño del archivo: 1 mb    Fabricar: Chamberlain  
Categoría: Vídeo

1 2 PIR Motion Sensor Assembly & Test Connect PIR Motion Sensor box to mounting plate with silver screw. Tighten screw until PIR Motion Sensor stays in place when repositioned. A Install 4 AA Alkaline batteries (not provided). (Lithium batteries recommended for colder environments.) B Ensure batteries do not touch circuit board. Test PIR Motion Sensor by waving hand in front of sensor. Test light should flash after several seconds. Plug in Base Station. Adhere rubber pads to bottom. 4 AA Alkalin

Chamberlain THE PROTECTOR SYSTEM 916GA

Descargado: 3Tamaño del archivo: 2 mb    Fabricar: Chamberlain  
Categoría: Vídeo

The Safety Sensors are designed to detect an obstacle in the path of the electronic beam and stop the gate operator. CARTON INVENTORY Verify carton inventory below. Hex Head Bolt (2) Wing Nut (2) IMPORTANT INFORMATION ABOUT THE SAFETY SENSORS When properly connected and aligned, the sensor will detect an obstacle in the path of its electronic beam. The sensors must be installed so that the sending and receiving eyes face each other across the gate, no more than 24" (61 cm) above the groun

Chamberlain TCR2

Descargado: 1Tamaño del archivo: 247 kb    Fabricar: Chamberlain  
Categoría: El receptor y el amplificador

Power: 12Vdc or 18 to 34Vac/Vdc, @ 30ma RF Frequency: 300 or 310 MHz Accessory Transmitters: TC1, TC2 and TC4 The TriCode® digital receivers are designed for use with automatic garage/gate operators and access control systems. All TriCode® products may be matched with Linear/Delta-3TM, Multi-CodeTM, and StanleyTM radio products which may already be installed. To prevent possible SERIOUS INJURY or DEATH from electrocution: • Be sure power is NOT connected BEFORE installing the receiver. To preven

Chamberlain Swing GATE

Descargado: 23Tamaño del archivo: 3 mb    Fabricar: Chamberlain  
Categoría: La puerta automática

2. If you want the gate to stop when a vehicle drives onto the Interrupt Loop and to close when the vehicle drives off the Interrupt Loop, on switch S1, set SLIDE to OFF and ATG to ON. 3. If you want a closing gate to open when a vehicle drives on the Interrupt Loop, on switch S1, set SLIDE to ON and ATG to OFF. 4. If you want a closing gate to stop when a vehicle drives on the Interrupt Loop and an opening or closing gate to close when the vehicle drives off the Interrupt Loop, on switch S1, se

Chamberlain SL930

Descargado: 8Tamaño del archivo: 217 kb    Fabricar: Chamberlain  
Categoría: cargadores

Refer to the manual for all mounting and wiring instructions with the exception of page 14. For page 14, follow instructions shown below. WIRING CONTROL WIRING BATTERY BACKUP If the gate operator is already factory equipped with battery run, only the Right/Left Side switch and Mode 1 are supported (Figure 3). The Right/Left switch must to be set in the same position as the Right/Left switch on the main control board. (See page 22 for correctly setting the Right/Left switch on the control bo





Categoría