Iniciar sesión:
Clasificado: Nombre ↓   Descargas   Tarifa   Tamaño ↑  

Aube Technologies 144860

Descargado: 4Tamaño del archivo: 1 mb    Fabricar: Aube Technologies  
Categoría: Los termostatos

8. Press and the main display shows HOLD. 44002-01 r051807 PERMANENT OVERRIDE SETTINGS SELECT HOLD TYPE12345 44002-01 r051807 1. Touch the temperature icon (). The selected icon will flash and SET OVERRIDE TEMPERATURE appears. 2. Touch the or sign to adjust the setting. 3. Press and the screen displays SELECT HOLD TYPE. 4. Touch the or sign to select PERMANENT HOLD. 5. Press and the main display shows HOLD. 44002-01 r051807 VACATION OVERRIDE SETTINGS SELECT HOLD TYPE1325466 44002-01 r051807 1. T

Aube Technologies 40120

Descargado: 4Tamaño del archivo: 790 kb    Fabricar: Aube Technologies  
Categoría: Los termostatos

Set the Set Temperature slider to the desired temperature. 2. The System Switch determines the operating mode of the thermostat. Select Off or Heat. 3. The Fan Switch should normally be located in the Auto position. To run the fan continuously, slide the Fan Switch to the On position. Note: In Auto , The fan will be turned on along with normal operation of your system. In a normal gas or oil furnace, the fan will be turned on by your furnace after its warm-up delay. indicators and adustment 1. T

Aube Technologies 40135

Descargado: 7Tamaño del archivo: 791 kb    Fabricar: Aube Technologies  
Categoría: Los termostatos

Tools This thermostat includes two #8 slotted screws and two wall anchors for mounting. To install your new thermostat, you will need the following supplies: Flat-head screwdriver ...................................................................................... Small Phillips-head screwdriver ...................................................................................... Hammer ...................................................................................... Electric drill and 3

Aube Technologies 40170

Descargado: 5Tamaño del archivo: 714 kb    Fabricar: Aube Technologies  
Categoría: Los termostatos

2 24 05060780 90Thermometer Battery Indicator 05060780 90Thermometer Battery Indicator indicators and adustment indicators and adustment 1. The Thermometer indicates the room temperature. 2. The Battery Indicator displays two battery conditions. The first warning is the Weak Battery Warning, indicated by the Battery Indicator flashing once approximately every three seconds. When this warning appears, install two fresh AA alkaline batteries at your earliest convenience. 3. The second warning is t

Aube Technologies 42710-01

Descargado: 4Tamaño del archivo: 2 mb    Fabricar: Aube Technologies  
Categoría: Los termostatos

Press the Up or DOwN buttons to adjust the temperature setting as desired. 4. Press and release HOlD/RETURN to return to the normal display. 32 hometodayHOME TODAY hometodayHOME TODAY METHODS OF OPErATIOn 3. HOME TODAY OVErrIDE Overrides the programmed settings during a time you would not normally be home. Pressing Home Today during the first or second programs of the day will override the programs until the fourth program begins. The thermostat will then go back into normal mode. Pressing Home

Aube Technologies 42711-01

Descargado: 5Tamaño del archivo: 1 mb    Fabricar: Aube Technologies  
Categoría: Los termostatos

follow the instructions on pages 42-43 to change batteries. 2. Filter change indicator - will flash after 400 hours of system use as a reminder to check or change your filter. Press and hold the Filter button for 3 seconds after changing the filter to reset the filter timer. (Pressing the Filter button for less than 3 seconds will cause the Filter change indicator icon to appear. The filter timer will not be affected unless the button is held for more than 3 seconds.) 40 HEATCOOLsystemoffheatcoo

Aube Technologies 42999 44050S

Descargado: 0Tamaño del archivo: 456 kb    Fabricar: Aube Technologies  
Categoría: Los termostatos

NOTE: Do not connect a “Common” wire this thermostat. Tape up the wire and do not use. Mount Snap open the your thermostat the release tab on the the thermostat. Position wallplate on through large opening. Then level appearance. Mark holes if existing holes Hunter Thermostat holes. Drill holes with 3/16" bit and gently Reposition wallplate to wall, pulling through large opening. Insert mounting screws provided into wall anchor and tighten. 2.) FIGURE 2 14-15Installation Selector Switches The he

Aube Technologies 43057

Descargado: 0Tamaño del archivo: 2 mb    Fabricar: Aube Technologies  
Categoría: Los termostatos

Up Button Down Button fanautorefreshon Heating or Cooling 1. To set the system for Heating, slide the “system” switch to “heat”. To set the system for Cooling, slide the “system” switch to “cool”. 2. Slide the “fan” switch to “auto”, refresh”, or “on”. Setting Options The following Options are available on your thermostat: 1. 1st stage span - The factory setting for Stage 1 heating and cooling is 1, meaning that your thermostat will cycle at 1°F (0.5°C) above and below the set temperature in Sta

Aube Technologies 43153

Descargado: 5Tamaño del archivo: 219 kb    Fabricar: Aube Technologies  
Categoría: Los termostatos

n The number of wires in your system can be as few as two (for heat only systems), as many as eight, or any number in between. If you follow the labeling procedures correctly, you do not have to be concerned about how many wires there are. n There is often no terminal marking on the existing thermostat of two wire, heat only systems. Just connect either of the wires to the RH terminal, then connect the other wire to the W terminal to complete the circuit. n IMPORTANT! BEFORE DISCONNECTING ANY WI

Aube Technologies 43154

Descargado: 36Tamaño del archivo: 293 kb    Fabricar: Aube Technologies  
Categoría: Los termostatos

/return Filter Change Indicator Your thermostat measures the number of hours your heating and cooling system has been in use. To maximize your system’s performance and energy efficiency, change or clean your filter regularly. M T W TH F SA SU SET TEMP AM 2PM FILTER filter COOL TEMP seconds. The display will blink, and the timer will be reset to zero. Note: Pressing the Filter Key at any time for less than 3 seconds will cause the Filter indicator to appear on the LCD. This is only to confirm key





Categoría