holes in the dispenser, as shown (adapters must be compressed on foam and level with dispenser). C. Fasten each adapter with the two screws provided in kit. D. Apply foam tape to the edge of adapters and on top of existing rear foam tape. 3. Ice machine installation: A. Position ice machine on dispenser. B. Proceed to ice machine installation manual for electrical and water hook-up and start-up procedure. Manitowoc Ice, Inc. 2110 South 26 Street, P.O. Box 1720, Manitowoc, WI 54221-1720 US

Warning: Do not drill through interior liner. Attach with the screws provided. Apply foam tape to the edge of the adapters, as shown, and on the front and rear of the bin between the adapters. Note: We recommend using RTV at intersections and along front inside edge of foam tape to prevent water tracking. Use double tape thickness with S-series ice machines. Refer to ice machine installation manual for ice machine installation procedures. B. C. D. E. F. Manitowoc Ice, Inc. 2110 South 26

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the unit’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit. 3 LOCATION OF CONTROLS AND INDICATORS 3

Remove the existing foam tape and ice deflector from bin. For the K00156 kit, slide the support brackets onto the deflectors in the kit. For the K00157 kit, use the deflector from the bin. Locate, as shown on the drawing below. Secure the deflector(s) to the bin with the screws removed earlier. Apply approximately 10 1/2” (26.7 cm.) of foam tape to the bottom front edge of the adapters between the bin and the adapters. Place the adapters on the bin, as shown. Using the adapters as templates,

Box 1720, Manitowoc, WI 54221-1720 USA Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 8005843 Web Site - Rev. 04/12/02 Cornelius ABS or ED150 Dispenser

NOTE: Do not drill deeper than 1/4” past the sheet metal. Use a drill stop! 3. Fasten adapter to dispenser using the four (4) #8 screws supplied with the adapter kit. 4. Set the ice machine on top of the adapter. Align holes in ice machine front angle with the rivnuts on the adapter. 5. Secure the ice machine to the adapter with two (2) #8-32 thumbscrews supplied with the ice machine. 6. Set the front bin cover onto the dispenser. The back flange of the bin cover will latch onto the adapter.

Refrigerant oil must be used to lubricate the fittings. 4. Leak check all joints. 5. Place the four labels, 8136193, included, as follows: two on the ice machine (one by each serial plate), one, as shown below, and one at the discretion of the installer. 6. ATTENTION INSTALLER: Add the following refrigerant at the time of installation: Q-0600 Series - add four (4) pounds Q-0800 Series - add four (4) pounds Q-1000 Series - add two (2) pounds Q-1300 Series - Add nothing Manitowoc Ice, Inc. 2

PARTS LIST: Item Description Qty. P/N 1. Ice Chute Weldment 1 6639714 2. Top Cover 1 6870914 3. Water Shield 1 6639814 4. Top Mounting Bracket 1 6639914 5. Bottom Mounting Bracket 1 6640014 6. Bin Thermostat 1 6025014 7. Bin Thermostat Bulb Mounting Bracket 1 6091314 8. Electrical Box Front Cover 1 6207014 9. Tie Plate 1 6273014 10. Installation Instructions 1 8003293 11. Label -Wiring Diagram 1 8106243 12. RTV Sealer (3 oz. tube) 1 9100691 13. Foam Tape 114" 9202483 14. Screw #10-24 x 5/8" P.P.

This is normal and not a fault of the appliance. The Sentry System is monitoring the duration of large swings in temperature to protect your contents, and may alert you to this event. See “Reset Alarms” section on page 4. Help Prevent Tragedies Each year children die because they climb inside a discarded refrigeration product, get trapped inside and suffocate. Take precautions to prevent such tragedies by removing the door, taping or chaining it shut before discarding. OBTAINING SERVICE If You D

The control automatically reads and stores the interior temperature every five minutes. The data can be cleared by pressing the “SET” and “ON/OFF” keys simultaneously while the value is displayed. Minimum Stored Temperature (tLO): Press and hold 3. the “SET” key to display the minimum temperature stored. The control automatically reads and stores the interior temperature every five minutes. The data can be cleared by pressing the “SET” and “ON/OFF” keys simultaneously while the value is displaye