Continue to Final Assembly. C 4 99-8214KITASSEMBLY99-8214KITASSEMBLY DOUBLE DIN HEAD UNIT PROVISION A 1 Slide the aftermarket radio unit into the factory brackets and secure the unit to the brackets using the screws supplied with the head unit. (Figure A) 2 Secure the aftermarket radio unit and factory bracket assembly into the sub dash. (Figure B) 3 Place the Double DIN trim plate into the back of the radio housing, then attach the clock/hazard switch brack- et assembly using the (4) #6 x 3/8”

Locate one of the Left Brackets and mount it to the “L” side of the Pocket with (2) #6 x 1/4" Phillips Flat Head Screws. Next locate one of the Right Brackets and mount it to the “R” side of the Pocket with (2) #6 x 1/4" Phillips Flat Head Screws. (Figure A) 3 Mount the factory brackets to the shaded bosses (Fig. B2) with (4) #8 x 1/4" Phillips Pan Head Screws supplied and mount the entire assembly to the sub-dash. (Figure B) 1 98-8999 POCKET ASSEMBLY SUBARU POCKET 1 Disconnect the negative

1 Kit Assembly: pg. 2 Final Assembly: pg. 3 WIRING AND ANTENNA CONNECTIONS (Sold Separately) • 40-EU10 - European antenna adapter • 70-9003 - European harness a 1-800-221-0932 Q REV. 04-17-09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION DASH DISASSEMBLY 99-9303 BMW Z4 2003-2008 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. NOTE: Make sure the vent on/off dials are in the middle position. 2 Using a small flat blade screwdriver, release th

A POWER HARNESS IS SUPPLIED TO ALLOW THE USER TO WIRE THE AFTERMARKET RADIO UP WITHOUT THE NEED TO PURCHASE A SEPARATE WIRE HARNESS. 70-8116INSTALLATIONINSTRUCTIONSToyotaPowerandAmplifierBypassHarnessTHESE HARNESSES ARE DESIGNED FOR THE 2000-04 TOYOTA AVALON, 2000-06 TOYOTA CAMRY, 2003-05 TOYOTA CELICA, 2001-06 TOYOTA HIGHLANDER, 2000-06 TOYOTA LANDCRUISER AND THE 2000-03 TOYOTA SOLARA WITH THE AMPLIFIED JBL SYSTEM. A POWER HARNESS IS SUPPLIED TO ALLOW THE USER TO WIRE THE AFTERMARKET RADIO UP W

(Figure A) 3 Remove (4) Phillips screws securing climate control and remove. (Figure B) 4 Unclip and remove the panel surrounding radio including A/C vents. (Figure C) 5 Remove (4) Phillips screws securing radio to remove. (Figure D) B D C 1 95-7419 KIT ASSEMBLY 2005-06 NISSAN ALTIMA DOUBLE DIN HEAD UNIT PROVISION 1 Snap the 95-7419 trim plate into the radio trim panel. (Figure A) 2 Slide the DDIN radio unit into the factory brackets and secure the unit to the brackets using the scre

INSTALLATION INSTRUCTIONS FOR PART 99-7606 INSTALLATION INSTRUCTIONS FOR PART 99-7606 Torx T-10 Driver • Small Flat Blade Screwdriver • Phillips Screwdriver KIT FEATURES • DIN Radio Provision with pocket • ISO Radio Unit Provision with pocket • Double DIN Radio Provision • Stacked ISO Head Units Provision A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Pocket • G) (6) Panel Clips • H ) Two Sided Tape (Not Shown) KIT COMPONENTS 99-76

1 1993-1995 Mercury Villager /1993-1995 Nissan Quest ............... 2 1996-1998 Mercury Villager/ 1996-1998 Nissan Quest ............... 3 1999-2002 Mercury Villager /1999-2003 Nissan Quest................ 4 1995-1999 Nissan Sentra /1995-1998 200 SX............................. 5 1995-1998 Nissan 240 SX............................................................ 6 1998-2001 Nissan Altima ............................................................. 7 1998-2001 Nissan Frontier/2000-2001 Nissan X

1,2 Kit Assembly ....................................... 3,4 Final Assembly 99-7319 DASH DISASSEMBLY 2004-2006 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove panel surrounding shifter including cup holders. (Figure A) 3 Remove (2) Phillips screws at base of panel surrounding radio and a/c controls. (Figure B) 4 Unclip and remove panel surrounding radio and a/c control. (Figure C) KIA AMANTI A 1 99-7319 DASH DISASSEMBLY 2004-200

• A) Radio Housing • B) Radio Housing Brackets KIT COMPONENTS A B C D APPLICATIONS Toyota Tacoma 2005-2011 • C) Radio Housing Trim Panel • D) ISO Brackets • E) ISO Trim Plate • F) (4) #6 x 3/8” Phillips Pan Head Screws • G) (4) #8 X 3/8” Phillips Truss Head Screws • H) Double DIN Trim Plate • I) Clock/Hazard Switch Bracket E F G H 99-8214TB 99-8214TG TOOLS REQUIRED: I WIRING AND ANTENNA CONNECTIONS (Sold Separately) Harness: • 70-1761 - Toyota harness 1987-up • TYTO-01 - Toyota amp interface har

. . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . 3 -DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . .4 -ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 5 -Double DIN /Stacked ISO Mount Units Radio Provision . . . . . . . . . . . . .6 Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWEREnhanceyour installation and fabrication skillsbyenrolling inthe most