: Shut off the power to the furnace before removing blower compartment door to avoid injury from moving parts. A. ANNUAL INSPECTION The homeowner must have this furnace professionally inspected at the beginning of each heating season by a qualified heating contractor to ensure proper operation. 11 All installations and services must be performed by qualified service personnel. NOTICE: This furnace has been shipped from the factory with a permanently lubricated circulating air blower motor. Any m

7. No attempt should be made to restart the unit in the event that gas to the main burner has been shut off. Contact a qualified heating contractor before restarting the furnace. All installations and services must be performed by qualified service personnel. 8. The furnace should be inspected annually by a qualified heating contractor. 9. : Do not use this furnace if any part has been under water. Immediately call a qualified heating contractor to inspect the furnace and to replace any part of

If fittings are loose or if blockage or corrosion is suspected to be a problem, contact a qualified heating contractor. Make sure horizontal runs of the flue have an upward slope away from furnace of 1/4" per foot minimum and are physically sound without holes, cracks or signs of corrosion. There should be no sign of moisture or vent gas leakage at any vent connection. ADDITIONAL REQUIREMENTS OF FURNACES VENTED THROUGH THE SIDE OF THE HOUSE WITH NO CHIMNEY. a. Such horizontally vented furnaces s

If you then smell gas, STOP! Follow Step B in the previous safety information. Go to the next step if you don’t smell gas. 7. Turn gas control knob counterclockwise to “ON” position. (For gas valves with a switch, move the switch to the “ON” position). 8. Replace front door. 9. Turn on electric power to the appliance. 10. Set thermostat to desired setting. 11. Follow the instructions “To Turn Off Gas To Appliance” and call a qualified heating contractor or gas supplier if the appliance will not

10. Should overheating occur or the gas supply fail to shut off, shut off the manual gas valve to the furnace before shutting off the electrical supply. : If you suspect there is a problem with the furnace, its venting system or any other related problem, immediately contact a qualified service agency. 11. Your furnace should be described by the model number and serial number when contacting a qualified heating contractor. This important information is located on the rating plate behind the fron

Outside vent and outside combustion air termination: the outside vent terminations should be inspected to insure that they are clear and free of obstruction by ice, snow, debris, of vegetation. Any obstruction of the terminal should be carefully removed without damaging the vent terminal. If ice has formed on the outside terminals themselves, it should be removed. 14 All installations and services must be performed by qualified service personnel. 3. Flue Pipe Connection & Chimney for MDA1/MHA1:

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. WHAT TO DO IF YOU SMELL GAS: • DO NOT TRY TO LIGHT ANY APPLIANCE. • DO NOT TOUCH ANY ELECTRICAL SWITCH; DO NOT USE ANY PHONE IN YOUR BUILDING. • LEAVE THE BUILDING IMMEDIATELY. • IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A NEIGHBOR’S PHONE. FOLLOW THE GAS SUPPLIER’S INSTRUCTIONS. • IF YOU CANNOT REACH YOUR GAS SUPPLIER; CALL THE FIRE DEPARTMENT. INSTALLATION AND SERVICE MUST BE PERFOR

SAFETY INFORMATION 1 II. GENERAL INSTRUCTIONS 5 III. FURNACE OPERATION 10 A. WARNINGS BEFORE OPERATING 10 B. OPERATING INSTRUCTIONS 10 C. SHUTDOWN PROCEDURE 11 IV. HOMEOWNER/USER MAINTENANCE INSTRUCTIONS 11 (ROUTINE MAINTENANCE) A. ANNUAL INSPECTION 11 B. FILTER MAINTENANCE PROCEDURE 12 C. VISUAL INSPECTION PROCEDURE 14 All installations and services must be performed by qualified service personnel. I. SAFETY INFORMATION This and the following page contain reproductions of the various warning an

For operation at elevations above 2,000 feet (600 m), equipment ratings shall be reduced at the rate of 4 percent for each 1,000 feet (300 m) above sea level. For additional information, refer to the latest edition of the National Fuel Gas Code. Checking The Burner Flame .. CAUTION: The furnace model series CDX1 and CHX1 are sealed combustion designs that do not require an air shutter adjustment (air shutters are not used) for proper flame characteristics. The burner box access cover must always

Heats rooms that were cool with previous furnace. So far we have used less kw of power each month compared to the previous year. ” Bob Williams, VP ofRossoe Energy Systems & Oil Company When you want to experience exceptional comfort, increased efficiency, and quieter operation while still receiving the handcrafted quality and proven warranty of Thermo Pride’s traditional oil furnace, select the Premiere Oil Furnace with the ECM variable-speed blower motor. Since the ECM motor automatically ad