Retire la cubierta del amortiguador de chispas. 4. Saque la pantalla del amortiguador de chispas de la cubierta del amortiguador de chispas. 5. Limpie la pantalla del amortiguador de chispas con un cepillo de alambre, o cambiela. 6. Vuelva a instalar la pantalla del amortiguador de chispas, la cubierta del amortiguador de chispas y el tornillo. LIMPIEZA ADVERTENCIA: Para evitar graves lesiones personales, apague siempre su unidad y espere que se enfrie antes de limpiarlo o realizar cualquier tip

WARNING: Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition. 1. 2. 1 2 3 Figure 3-6 Controls and Features 4 11 Blade Control The blade control is attached to the upper handle of the mower. Depress and squeeze it against the upper handle to operate the unit. Release it to stop engine and blade. WARNING: This bl

Less choking may be necessary due to variations in temperature, grade of fuel, etc. Little or no choking will be needed when the engine is warm. 3. Place the throttle in the "START" (1/2-3/4 throttle) position. Never start engine at full throttle. 4. Place the PTO switch to the "OFF" position. 5. Place the speed control lever in neutral ("N"). 6. Depress brake pedal all the way down. NOTE The speed control lever will automatically return to neutral when the brake pedal is pressed all the w

If a mower is mounted on the tractor, the mower must be lowered to facilitate removal of the filter. Remove the throw-away-can-type filter and replace with a new filter after the first 10 and 50 hours of operation, and every 100 hours of operation thereafter. The filters can be obtained through your Cub Cadet Dealer under part number 723-3014. To remove the filter, turn the filter counterclockwise using an automotive-type filter wrench. Before installing the new filter, apply a coating of oil

Adjust as follows: (See Figure 32.) 1. Loosen (do not remove) the hex bolt and nut at the stationary idler bracket. 2. Slide the idler pulley upward to tighten the belt. Tighten hex nut and bolt. When no adjustment is left, have belt replaced. 1. Idler Pulley 2. Hex Nut 3. Bolt 4. Drive Belt 21 DRIVE BELT REPLACEMENT If drive belt replacement is required, contact your authorized Cub Cadet Dealer. BATTERY INFORMATION A WARNING A. Battery acid must be handled with great care as conta

Antes de comenzar la operacion de una herramienta motriz, use siempre gafas o lentes de seguridad que indiquen que cumplen con las normas ANSI-Z87.1, y una mascara facial completa cuando sea necesario. • SEGURIDAD DE LA RECORTADORA Y CORTADORA DE MALEZAS ADVERTENCIA: Los objetos que salen despedidos y la cortadora giratoria pueden causar graves lesiones. Mantenga a los espectadores, especialmente a los ninos y animales domesticos a no menos de 50 pies (15 m) de distancia del area de corte. Debe

Read it carefully before assembly and operation of the equipment! CONGRATULATIONS on your the purchase pf your new Brinly-Hardy Lawn Sweeper! Your lawn sweeper is designed, engineered and manufactured to give you the best possible dependability and performance. CUSTOMER RESPONSIBILITIES Please read and retain this manual. The instructions enables you to assemble and maintain your lawn roller properly. And please, always observe the "Safety" instructions. TABLE OF CONTENTS SAFETY ............ ...

Remove the belt guard. 3. Remove the front PTO drive belt from the double drive pulley, and replace with a new belt. 4. Install the double drive pulley belt guard in the same position noted in step 1. Secure the belt guard in proper position using the washer and bolt. When the PTO drive belt has been replaced, the mower deck reinstalled onto the tractor, and the front PTO drive belt positioned onto the engine drive pulley and the idler pulley, refer to "DOUBLE DRIVE PULLEY BELT GUARD ADJUSTME

Le Droit des Etats vis a vis de la presente garantie : la presente garantie vous confere certains droits juridiques et vous pouvez beneficier d'autres droits lesquels varient d'un etat a l'autre. Pour obtenir l'adresse du distributeur reparateur le plus proche, composez le : 1-877-282-8684. Cub Cadet LLC PO Box 361131 Cleveland, OH 44136-0019 Manuel del Dueno/Operador Recortador de 2 Ciclos Modelo CC 3075 IMPORTANTE: LEA LAS REGLAS DE SEGURIDAD E INSTRUCCIONES DETENIDAMENTE P/N 769-00876 (10/03)

P.O. BOX 368023 CLEVELAND, OHIO 44136-9722 45” Snow Thrower Model 1345 SWE PRINTED IN U.S.A. Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forestcovered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California