Plate glass mirror shall have all four edges polished. MODEL NO. WALL OPENING A B C OVERALL SIZE D E MIRROR TYPE 935P24WH 14 24 3-1/2 16 26 Polished Edge 935P34WH 14 34 3-1/2 16 36 Polished Edge 936P24WH 14 24 3-1/2 16 26 Beveled Edge 936P34WH 14 34 3-1/2 16 36 Beveled Edge A Broan-NuTone LLC, 501 S. Wilhite Street, Cleburne, TX 76031 (1-800-325-8351) REFERENCE QTY. REMARKS Project Location Architect Engineer Contractor Submitted by Date Standard builder mode

Attn: Department of National Field Service, 4820 Red Bank Road, Cincinnati Ohio 45227-1599. Residents of Canada should write to:Broan-NuTone Canada, 1140 Tristar Drive, Mississauga, Ontario, Canada L5T1H9. Rev. 03/2001 Product specifications subject to change without notice. 4820 Red Bank Road, Cincinnati, Ohio 45227 Printed in U.S.A., Rev. 01/2004, Part No. 84762 DIRECTIVES D’INSTALLATION LIRE ET CONSERVER CES DIRECTIVES! Ventilateur de salle de bain MODELES: 8832WH, 8832SA et 8833 • Ne pas ins

1. Insert hanger bars in slots provided in housing. 2. Locate fan housing between joists so that the bottom of the housing is even with the planned finished ceiling. Extend the hanger bars to the joists. 3. Use screws or nails (not provided) to secure hanger bars to ceiling joists. INSTALLING DUCTWORK 1. Refer to Figure 2. Place duct collar over flanges at discharge opening of fan. Secure collar by snapping tabs into slots in flanges. 2. Run 4" round duct from outside to fan’s discharge opening.

1. Observe all requirements in these instructions and all markings appearing on the unit. 2. Check all operations of the unit after installation has been completed. 3. The housing must be grounded and the installed wiring must comply with all local electrical codes. 4. The flange of the rough-in housing MUST be flush with the finished plaster or drywall surface to assure proper and safe operation. 5. If plaster material, paint base, or paint is sprayed on the walls or ceiling, the inside of the

Drill small reference hole under location of VacPan™ to determine position in basement or crawl space. 2. Using a hole saw, cut access hole (3) in floor under cabinet. Position access hole (3) so that final fittings (7) can be installed by reaching through access hole (3). 3. Cut 6 3/4" long slot along kick (4) of cabinet. 4. Make terminal connections (5). 5. Slide VacPan™ (6) into slot and secure using #6 painted wood screws provided. 6. Reach through access hole (3) and make final fitting

El trabajo de instalacion y el cableado electrico deben ser realizados por una(s) persona(s) calificada(s) de acuerdo con todos los codigos estandares aplicables, incluyendo la construccion segun los estandares contra incendios. B. El flujo del aire de combustion necesario para el manejo seguro del equipo quemador de combustible puede verse afectado por el funcionamiento de esta unidad. Siga las pautas y estandares de seguridad del fabricante para el equipo de calefaccion como las publicadas por

Trimmed with aluminum top and bottom. Steel door backs shall be finished to match white cabinet finish. Cabinet shall have (2) fixed steel shelves. Broan-NuTone Storage Solutions, 501 S. Wilhite, Cleburne, TX 76031 (1-800-325-8351) REFERENCE QTY. REMARKS Project Location Architect Engineer Contractor Submitted by Date 80D A99044175 B

The Basic model is sold with a choice of a simulated oak or white flat panel door, shown – or your choice of custom door, sold separately.The Basic model is non-electric. Speakers Medicine Cabinets Range Hoods Fresh Air Systems Trash Compactors Ceiling Fans Ventilation Fans Sensing Fans Heaters Intercoms Chimes Central Vacuums NuTone® is America’s leading brand of residential built-in convenience products including door chimes, central vacuum systems, intercom systems, home theater speakers, med

Example: 24' (L) x 16' (W) x 8' (H) = 3072 ft 3 2. Divide the volume of space by 50 ft 3 to determine the maximum BTU/Hr the space can support. (volume of space – ft 3)/ 50 ft 3 = (Maximum BTU/Hr the space can support) Example: 3072 ft 3 / 50 ft 3 = 61.44 or 61,440 BTU/Hr the space can support. 3. Add the BTU/Hr of all the fuel burning appliances in the space. Vent-Free heater ________ BTU/Hr Gas appliance #1* ________ BTU/Hr Gas appliance #2 +________ BTU/Hr Total =________ BTU/Hr Example: Vent