Never allow the clamps to touch each other. b. When attaching a clamp to a battery post, twist or rock the clamp back and forth several times to make a good connection. This tends to keep the clamp from slipping off the terminals and helps to reduce the risk of sparking. 6. STOP/GO LITE INSTRUCTIONSWhen used properly, the STOP/GO LITE will indicate whether the clamp connections will be correct. Connect the Positive (RED) clamp to the Positive (POS,+) battery post. Touch the contact button of the

e. NEVER smoke or allow a spark or flame in vicinity of the battery or engine. f. Be extra cautious to reduce risk of dropping a metal tool onto the battery. It might spark or short circuit the battery or other electrical parts that may cause an explosion. g. Remove personal metal items such as rings, bracelets, necklaces, and watches when working with a lead-acid battery. A lead-acid battery can produce a short circuit current high enough to weld a ring or the like to metal, causing a severe bu

The Company hereby warrants to the Purchaser that if the Product, or any part thereof, shall prove to be defective due to improper workmanship or materials at any time up to and including one (1) year from the date of Product's purchase at retail, then the Company shall repair or replace the Product, or any part thereof, as the case may be, at the Company's option, without charge to the Purchaser for parts and labor, provided that Purchaser follows the procedures set forth herein. This limited w

Designed to meet the needs of the most demanding professional with 16 rates of charge and 75 Amp continuous charge with 375 Amps Crank Assist at 12 Volts. 25% more engine start than previous model. UL and CSA listed for indoor and outdoor use. “SAFE IN ANY WEATHER”. (6002 Charger Specilications M0DÜ IS ll M B i R 6001 A 6002 B Jl CON IINUOUS RBTIlUß )00/75 A ■ 100/80 A mnmiiRMiP. RECTIFIER SHIPPING LIMITED DIMENSIONS WARRANT! mmoi 5 Years 5 Years 26"xl6"xl4’ 26"xl6"xl4' 58 lbs

Designed to meet the needs of the most demanding professional with 16 rates of charge and 75 Amp continuous charge with 375 Amps Crank Assist at 12 Volts. 25% more engine start than previous model. UL and CSA listed for indoor and outdoor use. “SAFE IN ANY WEATHER”. (6002 Charger Specilications M0DÜ IS ll M B i R 6001 A 6002 B Jl CON IINUOUS RBTIlUß )00/75 A ■ 100/80 A mnmiiRMiP. RECTIFIER SHIPPING LIMITED DIMENSIONS WARRANT! mmoi 5 Years 5 Years 26"xl6"xl4’ 26"xl6"xl4' 58 lbs

See the section below on Palm Desktop for installation instructions. If both Palm Desktop 4.1 and LS1M Synchronizer are installed, you will see this window appear when you hot- synch: The saved logs will appear in the list. Click on one to get more information at the bottom of the screen. You can also select multiple items by holding down the Control key on the PC keyboard or using the Select All button. You can Delete the selected logs, or use Delete All to delete all saved logs from the PDA. T

To do a hard reset, hold the power button down, press the reset button (hole), wait for the “Palm Powered” screen to show up, then let go of the power button. Press the page-up button to confirm, and the Palm will reset itself. It will prompt you to recalibrate the touch screen. Just follow the directions and when you’ve completed the calibration, your PDA will be ready to use again. Any lost programs can be restored by doing a hotsync, which will put it back to the same condition it was when th

The LS1M Scanner is a scan tool that can retrieve engine parameters and trouble codes from GM vehicle using the VPW OBD-2 protocol. That includes most GM cars & trucks from 1996 to 2006. To verify compatibility of your vehicle to the LS1M scanner, look for the diagnostic connector under the dash, on the driver’s side. It’s a 16-pin connector with pins 1-8 across the top & pins 9-16 across the bottom. The VPW protocol uses pins 2, 4, 5 & 16, so these positions should have a metal insert present.

A SPARK NEAR THE BATTERY MAY CAUSE BATTERY EXPLOSION. TO REDUCE THE RISK OF A SPARK NEAR THE BATTERY: a. Check the polarity of the battery post. The POSITIVE (POS, P, +) usually has a larger diameter than the NEGATIVE (NEG, N, -) post. b. Attach at least a 24 inch long 6-gauge (AWG) insulated battery cable to the NEGATIVE (NEG, N, -) battery post. c. Connect the POSITIVE (RED) charger clamp to the POSITIVE (POS, P, +) post of the battery. d. Position yourself and the free end of the cable as far

The second stage is a slow charging to restore the battery to full charge. READ AND FOLLOW ALL PRECAUTIONS AND WARNINGS IN YOUR INSTRUCTION MANUAL BEFORE ATTEMPTING TO CHARGE SULFATED BATTERIES. FAILURE TO OBSERVE THESE WARNINGS MAY RESULT IN PROPERTY DAMAGE OR SERIOUS PERSONAL INJURY OR DEATH. To recharge a sulfated battery: 1. Attach the battery clamps as described in the instruction manual. 2. Always use the chargers lowest rate when turning the charger on. Set the charger to the chargers hig