• Los Jumpers Stereo/Mono son sacadosde los pines para jumpers • Single Mono Amp se conecta a la entrada Stereo/Mono Left • Mono Amp Left se conecta a la entrada Stereo/Mono Left • Mono Amp Right se conecta a la entrada Mono Right NOTA: El Power 250m2, Power 500m y Power 250m deben usar el encendido remoto en modo activado para un mejor funcionamiento . Adaptador utilizado solo en los amplificadores Power 500m • El Adaptador del Power 500m debe conectar la banda del amplificador del cable de Int
. . . . . . . . . . . . . . . . . . . . 14 Informacion sobre la garantia limitada. . 15 2009 Rockford Corporation.Todos los derechos reservados Rockford Fosgate, el logotipo Rockford Fosgate, el logotipo POWER y el logotipo PUNCH son marcas comerciales registradas o marcas registradas de Rockford Corporation. 2 INICIO .Bienvenidos a Rockford Fosgate! Este manual ha sido creado para proporcionarle informacion al dueno, vendedor y tecnico de instalacion. Para quienes desean informacion rapida sobr
Use the section of cable that was trimmed earlier and connect it to the other end of the fuseholder. 4. Strip 1/2" from the battery end of the power cable and crimp a large ring terminal to the cable. Use the ring terminal to connect to the battery positive terminal. DO NOT install the fuse at this time. INSTALLATION 5. Prepare the BLACK wire (Ground cable) for attachment to the amplifier by stripping 1/2" of insulation from the end of the wire. Insert the bared wire into the GND terminal and ti
. . . . . . . . . . . . . . . . . . . . . . . 2 Safety Instructions . . . . . . . . . . . . . . . . . . . 3 Design Features . . . . . . . . . . . . . . . . . . . . . 4 Installation . . . . . . . . . . . . . . . . . . . . . . . 5-9 Installation Considerations . . . . . . . . . . . 5 Mounting Locations. . . . . . . . . . . . . . . . 6 Battery and Charging. . . . . . . . . . . . . . . 6 Wiring the System. . . . . . . . . . . . . . . . . 6 Using Passive Crossovers. . . . . . . . . . . . 9 Remote Pun
+ – + Speaker Terminal – Speaker Terminal 2W min. 2W min. R Gain Pass Thru R GainBalanced InputL L Bass EQ EZ BridgedPass Thru R Speaker + L – Speaker – R + Operacion mono/estereo • Los conectores de entrada RCA se conectan a ambos canales derecho e izquierdo • El conmutador de senal de entrada se colocara en Unbalancedpara las entradas RCA • El conmutador de fase del canal izquierdo estara en 0 grados • El conmutador de fase del canal derecho estara en 180 gradoscuando se requiera operacion mon
The voltage should measure between 11.5V - 15.5V. If voltage is notfound, check the battery, fuse, fuse housing and wire connections. Fix, repair, or replace accordingly. 2. If the amplifier still does not play, check the voltage at the amplifier’s remote turn-on lead. The voltage should measure between 11V - 15V. a. If voltage is above or below the prescribed measurements, check for proper connections and have the head unit checked by an Authorized Dealer or Service Center. b. If the remote tur
Running the wires inside the vehicle provides for the best protection. 7. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect wires routed through holes in metal. 8. ALWAYS protect the battery and electrical system from damage with proper fusing. Install a fuseholder and fuse within 18” (45.7 cm) of the battery terminal to safeguard from possible damage or injury. This fuse and fuseholder is included with the Series 1 amplifier. (See installation instructio