IMPORTANT: Please fill out the SNAPPER Product Registration Card immediately and mail to: Snapper's Product Registration Center, P.O. Box 1379, McDonough, Georgia 30253 11 unit breakdown & parts list 12 unit breakdown & parts list S SSn nna aap ppp ppe eer rrZ ZZ- --V VVa aac ccB BBl llo oow wwe eer rrU UUn nni iit ttG GGr rro oou uup pp4 448 88” ””, ,,5 552 22” ””, ,,6 661 11” ””M MMo ood dde eel lls ss Item Part No. Qty Description 1 3046782 1 WELDMENT, Blower Belt Guard 2 91121 1 NUT, 1/2-13

NO. 1691526 LANDLORD/1700 SERIES CART MFG. NO.1692085 printed in l/94-1GCCI ,.~.~~ ,.. :L..~ ~~: ‘in. . : :: .:.. :.,.: ~,: ‘:, .,.: : :. Table of Contents Page Standard Fastener Identification Chart....................................................... inside Front Cover Decals ....................................................................................................................................... 1 Specifications ..................................................................

8710 36" BLOWER ASSEMBLY MFG. NO. 1691373 42"BLOWER ASSEMBLY MFG. NO. 1691260 COLLECTION SYSTEM MFG. NO. 1691245 Table of Contents Safety Decals ------- . . ...................................... ..... Inside Front Cover Safety Rules , h . S ....................................................... 1 Installation - ? 36" Blower Assembly ...... .......................... ................. ............ 42" Blower Assembly .................................... ..............................

No. SV25550HC SV25650B 7085638 7085687 Model Mfg. No. SV25500HV SV25550HV 7085644 7085642 COMMERCIAL MODELS Before operating your new machine, read this manual carefully and pay particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 & 3. Remember that all power equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance with the operating instructions and common sense! NOTE: Specifications are correct at time of printing and are

4.2 IMPELLER REPLACEMENT The impeller is a wear item. The actual wear rate is dependant on the types of debris the machine has been used to pickup. If the machine develops unusual noise and/or vibration STOP the engine immediately. After allowing the engine to cool, proceed with the following steps. 1. In an open area where fumes can safely dissipate, drain fuel into an approved container. 2. Drain engine oil. 3. Remove sparkplug wire from sparkplug and secure away from sparkplug. 4. With engine

10 Service – Every 25 Operating Hours.......................................................................... 10 Storage – Out of Season.............................................................................................10 SECTION 4- ADJUSTMENTS AND REPAIR .................................................................. 11 Engine Adjustments & Repair .................................................................................... 11 Impeller Replacement..........................

Its purpose, aside from recommending standard operating procedures and routine service requirements, is to promote SAFETY through the use of accepted operating practices. Read, Understand and Follow the IMPORTANT SAFETY INSTRUCTIONS on Pages 2 & 3 of this manual and All SAFETY messages on the machine and its attachments before operating. 2.2.2 NOMENCLATURE The nomenclature picture above, Figure 1.1, shows the essential parts of the Yard Vacuum. It is recommended that all operators of this equipm

No. SV25550HC SV25650B SV25650B SV25650B 7085638 85633 7085634 1694489 COMMERCIAL MODELS Model Mfg. No. SV25500HV SV25550HV 7085644 7085642 Before operating your new machine, read this manual carefully and pay particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 & 3. Remember that all power equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance with the operating instructions and common sense! COPYRIGHT © 2003 SNAPPER PRO

1. Adjust height of vacuum inlet. For maximum debris pickup, inlet should be as close to debris as possible without blocking airflow and engine speed set to “FAST”. 2. Inspect debris bag. It must be properly attached to machine, in good condition, clean and dry with the top zipper fully closed. Make sure that the accessory plug is installed into front hole in vacuum nozzle. 3. Start engine. Not all debris pickup will require that the engine speed be set to “FAST”. You can experiment with vacuum

Lea el manual del operador para obtener información completa de seguridad, instalación, operación, mantenimiento y reparación. SIMBOLO A © © I«M—• SIGNIFICADO • SÍMBOLO DE ALERTA DE SEGURIDAD Indica peligro, advertencia o precaución. , Puede ser usado junto con otros símbolos o pictografías. • ADVERTENCIA - LEA EL MANUAL DEL OPERADOR Lea el (los) manual(es) del operador y siga todas las instrucciones de advertencias y seguridad. Dejar de hacerlo puede ocasionar lesiones graves al oper