Steps for other Windows operating systems will be noted beneath each screen shot. Step 1 At the Found New Hardware Wizard, select Install from a list or specific location (Advanced) and click Next. ruin J Nb> I Is rd’.“nra 'A'linrd Weltome li -the Four a N ew I lnrclWHiB Wl/nr[i I - hl-'.-ii "i-J c-: y u red .-I < i kv.-ii- ■ Hhtwt Coin 0 lei ' ) II pi mi hrtiilwrti h i:.«h wilh ,nn ■ iI.-

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user's guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference, in which cas

This switch integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in a highly fexible mini package. P/N:19G7MSW1G5+7G5G The Switch's Ports The Switch's Indicator LEDs Ports 1-5 At the rear site ofthe Switch, ports 1-5 are where you will connect your Computers to the Switch Power At the left site of the Switch, the power port is where you will connect the AC power adapter. Be sure to only use the AC power adapter that came with the Switch. Connect Computers to the Switch

Information contained herein is the property of AirLink Communications, Inc. and is produced for the purpose of detailing technology developed by AirLink Communications, Inc. and its employees. Reproduction or distribution of this document without the express written consent of AirLink Communications, Inc. is strictly prohibited. This document is subject to change without notice. O Copyright AirLink Communications, Inc, 2001. All rights reserved. Please send comments to: Email: pubs@AirLink.com

1A Quick Installation Guide Model # AKVM-4 Section 2 Installation ^ Before connecting any cable, please make sure all of your computers and their peripherals have been powered off. Otherwise, the KVM switch may not be set up properly. Step 1 Make sure all the computers that are to be connected to the KVM switch and their peripherals are powered-off. If not, power them off before you proceed with the following steps. Step 2 Connect the shared keyboard, monitor, and mouse to the main KVM un

1A Section 1 Section 1 This Quick Installation Guide only provides basic instructions. For more detailedinformation, please refer to the User’s Manual in the supplied CD. Getting Started Please refer to the following diagrams to determine which operating modeyou should use for your network. If you want to use the AP431W as an Access Point with minimal configuration, just connect it to yourexisting router or switch with a Cat. 5 network cable and then power it on. The Access Point is ready touse

See Fig. 1.1 Step 2 Make sure the printer is powered OFF, then connect one end of the USB cableto the USB port of the Print Server and attach the other end of the cable to the USBport of the printer. Step 3 Turn ON the printer. Step 4 Plug one end of the power cord into the Print Server and the other end into anelectrical outlet. Fig. 1.1 Section 2 Section 2 Configuring Client IP Address Note: The default IP address of the Print Server is 192.168.1.254 with a subnet mask of 255.255.255.0 The Pri

4.5 Step 9 Click Next. Step 10 Click Finish. Fig. 4.5 Step 11 Select the manufacturer and model of your printer and click Next. Note: If your printer is not on the list, clickHave Disk, insert the printer driver diskthat came with your printer, and click Next. See Fig. 4.6 Step 12 If a driver for the printer is alreadyinstalled, select Keep existing driver and click Next. Fig. 4.6 Step 13 Type in a name for your printer and click Next. For Windows 2000, selectif you want to set this printer as t

Otherwise, the print server will not be configured successfully. Please refer to your printer’s manual for instructions on how to install the printer driver. Before setting up the print server, please take note of your TCP/IP setting. Step 1 Click on Start, Run, and type command (for Windows 95/98/ME) or cmd (for Windows 2000/ XP) and click OK. Step 2 At the command prompt, type ipconfig and press Enter. Step 3 Write down the information for the IP Address, Subnet Mask, and Default Gateway. You

This integrated access device combines Internet gateway functions with wireless LAN and Fast Ethernet switch. Designed for the business and home, it saves you the cost of installing a separate modem and ISP line for each computer, while providing ready connection for the users, with or without network cables. Broadband network access is also gaining ground. However, allowing more than two computers to access the Internet at the same time means higher costs. Thus, there is a need to share one leg