Battery Pack Battery Latch LockedPosition UnlockedPosition Removingand Instal llingtheBatteryPack To install the battery pack: 1. Slide the battery pack into the pen tablet until it is firmly seated. Warning Keep your fingers clear of the area between the battery pack and the pen tablet when you install the battery pack. 2. Slide the battery latch into the locked position. Once the battery pack is installed, you can resume system operation or start your system and use the system as you normally

Note: Ensure that you have the “Headset Only” button turned off when using this feature Using a HEADSET Connect your headset to the socket underneath your digital phone (labelled #2 port – picture of a headset) Press the “HEADSET ONLY” button. The light will go red to indicate that you are in “headset mode” Place the handset on the hook. You are now free to use BOTH the handset receiver and the headset to make or answer calls. To make an outgoing call via your headset: Dial out directly from the

Units with single rating are 265-volt units. ge.com Power Connection Kits 230/208-Volt Line Cord Connection Units 230/208-Volt Sub-Base and Direct Connected Units Electric Line Cord Heat Kit BTUH RAK 15 8600/7100 RAK 20 11700/9600 RAK 0 17100/1 900 Electric Heater Watts Electric Heat Amps Min. Circuit Protection (Amps) 2550/2090 11.6/10.6 15 450/2820 15.5/14.1 20 5000/4090 22. /20. 0 Electric Heat Amps include electric heater and fan motor current draw. Each Line Cord Kit has an integral Leakage

The configuration of the electrical plug conforms to NEC standards for the circuit amperage and the position of the wires in the nine-pin connector determines the heater wattage and current requirements when it is plugged into the Zoneline chassis. The power connection kit is selected by the amperage of the circuit where it will be installed. Each line cord kit has an integral Leakage Current Detection and Interruption (LCDI) or Arc Fault Current Interrupter (AFCI) device as required by the Nati

Mobile Accessories ..Issue May 2004 Extend your Pocket LOOX 4xx to your needs. More convenience for your business trips and more functionality enabling easy working. Fujitsu Siemens Computers offers a vast range of accessories for your Pocket LOOX 4xx: cradle station, power supply devices, different storage media, wireless connectivity cards and special cases that provide maximum protection while transportation. Reliability • High quality and stability • Reliability of delivery • Everything you

3-2 Taking Care of the Pen............................................................................... 3-2 Calibrating the Point 510 Display Screen ................................................ 3-3 Determining When to Perform Pen Calibration......................... 3-3 Performing Pen Calibration........................................................... 3-3 Solving Problems ........................................................................................ 3-4 Suspended Pen Tablet Wi

In the event of compressor failure during heat pump operation, unit shall automatically switch to electric resistance heat to maintain selected room temperature regardless of outdoor temperatures. Specifications for Optional Internal Condensate Removal (ICR) system for 3900 or 5800 series heat pump units. The unit shall have a factory-installed Internal Condensate Removal (ICR) system to permit unit to automatically dispose of heat pump generated condensate water with no overflow to outdoors dur

Any procedures described in this document for operating Fujitsu products should be read and understood by the operator before such products are used. To ensure that Fujitsu products function without risk to safety and health, such procedures should be strictly observed by the operator. The development of Fujitsu products and services is continuous and published information may not be up to date. Any particular issue of a product may contain facilities not described herein. It is important to che

. . . . . . .2, 3 Operating Instructions . . . . . .4, 5 Additional Controls . . . . . . . . . . .5 Controls . . . . . . . . . . . . . . . . . . . .4 Normal Operating Sounds . . . . .5 Care and Cleaning Air Filter . . . . . . . . . . . . . . . . . . .6 Grille and Case . . . . . . . . . . . . . .6 Grille Frame Removal . . . . . . . . .6 Outdoor Coils . . . . . . . . . . . . . . .6 Installation Instructions Through-the-Wall Installation—Optional . . . . . . . .13 Window Installation . . . . . . .

. . ( . . ™ _ ) + . •§ ¶ ‡ fi ‹ . Y # @ fl › ¤ K ° . J H G I 5 6 4 7 8 OPERA TION TIMER AIR CLEAN COIL DR Y = A B D C 9 3 1 2 Fig. 5 Fig. 1 Fig. 4 Fig. 3 Fig. 2 Fig. 7 To facilitate explanation, the acompan ying illustra- in taioctnu ahla os pbeereanti odnra, whonw toe vsehrow al posible indicators; , the display wil only show those indicators apropriate to the curent op- eration. Fig. 6 SAFECTYO PRNECTAEUTNIOTNSS En-1 FEA TURES AND FUNCTIONS . En-2 NAME OF P A RT S En-3 PREP ARA TION En-4 OPER