SQ. END CAP into the front end of the ADJUSTMENT TUBE ASSEMBLY. 3. THE CONNECTOR PLATE IS NOT REQUIRED FOR THIS ASSEMBLY PLEASE DISCARD. 4. Assemble the ADJUSTMENT TUBE ASSEMBLY to the SEAT SUPPORT and BASE as shown on drawing, using two (2) 1/2 X 3-1/2 IN. BOLTS, four (4) 1/2 IN. WASHERS, and two (2) 1/2 IN. NYLOCK NUTS. (NOTE: THE BRACKET ON THE ADJUSTMENT TUBE ASSEMBLY IS FLUSH TO THE TOP OF THE TUBE, PLEASE ASSEMBLE FLUSH SIDE UP) 5. Insert one (1)2 IN. SQ. END CAP into the front end of t

X 1 IN. BUSHING PULLEY........................(Cl 162-1 4-1/2 O.D. X 1 IN. BUSHING PULLEY........................(Cl 161-1 20 .. 6 .. 2 3 PBF058 SELECTORIZED LAT MACHINE ASSEMBLY INSTRUCTIONS IMPORTANT: THE BODYSMITH SELECTORIZED LAT MACHINE MUST BE ASSEMBLED ON A FLAT LEVEL SURFACE TO ASSURE ITS PROPER FUNCTION. • PARABODY, INC. STRONGLY RECOMMENDS THAT THIS PRODUCT BE ASSEMBLED BY TWO PERSONS TO AVOID POSSIBLE INJURY. *** IMPORTANT *** KEEP ALL LOOSE FRAME CONNECTIONS LOOSE UNTIL INS

BOLT, one (1) 1/2 IN. WASHER, and one (1) 1/2 IN. LOW HEIGHT LOCK NUT. (NOTE: TIGHTEN SWIVEL SLEEVE ENOUGH THAT IT SWIVELS FREELY, YET IT DOESN'T WOBBLE) 10. Insert two (2) 1-3/4 IN. SQ. END CAPS into each end of the ADJUSTABLE SLIDE. 11. Insert the multiple hole end of the ADJUSTABLE SLIDE into the SWIVEL SLEEVE. (NOTE: BE SURE SWIVEL SLEEVE IS IN THE PROPER POSITION, SEE DRAWING) Attach the other end to the ADJUSTABLE SLIDE MOUNT on the BACK PAD, using one (1) 1/2 X 3 IN. BOLT, two (2) 1/2 I

or your PAP~,.BOD. CustomerSer~’,i~e Representath,e at: 1-800-32g-97~4 093 BODYSiVfIT~ PROSYSTEM ASSEMBLY PARTS L~ST SORT AND COUNT ALL PARTS BEFORE BEGYNNING ASSEiV[BLY ~AP, D%VARE: I_TCLM NAME/DESCPJPTION QTY .~/8 X 3-//4 IN. BOLT 2 ............................................................................................................. 3/~, X 3 IN. BOLT 14 ................................................................................................................. 3. 3/8 X 2-3/4 IN. B

(NOTE: REMOVE LOW PULLEY FOR EASE OF REMOVAL) 2. Insert four (4) 2 IN. SQ. END CAPS into all open ends of the BEARING HOUSING. 3. Insert one (I) 2 IN. SQ. END CAP into the end of the PULLEY MOUNT SUPPORT. 4. SECURELY assemble both the BEARING HOUSING and the PULLEY MOUNT SUPPORT to the MAIN UPRIGHT of the BODYSMITH PROSYSTEM, using two (2) 1/2 X 3-1/2 IN. BOLTS, four (4) 1/2 IN. WASHERS, two (2) 1/2 IN. LOCK WASHERS, and two (2) 1/2 IN. NUTS. NOTE: THE CONNECTOR PLATES ON THE BEARING HOUSING

ADAPTER PLATE allows the user to move up in 5 lb. weight increments. To attach the 5 lb. plate to the weight stack, carefully rotate the plate so that the cable will slide through the slot, then lower the plate onto the head plate and over the head plate shaft. Part # 6721301 1 Revision: 07/28/97

ADD-ON KIT WARNING: Read and follow all directions for each step to insure proper asembly of this product. ASSEMBLY INSTRUCTIONS CLASS H 1 PART # 7016801 Version: 216101 REV. B Revision: 03/23/01 PARTS LIST KEY PART # DESCRIPTION QTY KEY PART # DESCRIPTION QTY 1 6939201 WEIGHT PLATE 5 3 6978101 WEIGHT STACK LABEL 1 2 7095801 WEIGHT STACK SHAFT 1 4 6382301 WEIGHT PLATE BUSHINGS (10 CT) 1 STEP 1: • Insert two WEIGHT PLATE BUSHINGS (4) into each of the five WEIGHT PLATES (1) as shown

ADD-ON KIT WARNING: Read and follow all directions for each step to insure proper asembly of this product. ASSEMBLY INSTRUCTIONS CLASS H PART # 7016801 REV. B Version: 216101 Revision: 03/23/01 STEP 6: • Assemble the WEIGHT STACK PIN to the 20 HOLE WEIGHT STACK SHAFT as shown. • Screw the WEIGHT STACK CABLE into the 20 HOLE WEIGHT STACK SHAFT of the HEAD PLATE until the CABLE slightly pulls on the HEAD PLATE. • TIGHTEN cable jam nut securely! • CAREFULLY assemble and SECURELY tighten a

STEP 13: FIGURE 13 • Assemble one 3-1/2” PULLEY (24) into PRIMARY PIVOT (9) upper hole using one 3/8 X 8” BOLT (31), two 3/8” FLAT WASHERS (36), two 3/8 X 1-3/16” SPACERS (44) and one 3/8” LOCK NUT (34) and tighten securely • Assemble two 3-1/2” PULLEYS (24) into FRAME (1) using two 3/8 X 3-3/4” BOLTS (30), four 3/8 X 1-1/16” FLANGE SPACERS (42) and two 3/8” LOCK NUTS (34) and tighten securely. 9 34 36 24 42 44 31 30 1 3/8 X 3-3/4” 3/8 X 8” 16 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 14 • Re

FOR 220 GYM SYSTEM Version: 221101 TABLE OF CONTENTS Safety Statement.............2 General Notes..................3 Tools Required................3 Gym Layout.....................4 Parts list..........................5 Assembly Instructions.....5-10 General Maintenance.......11 Warranty Statement..........12 Product Services..............13 Insert-Registration Card IMPORTANT SAFETY INFORMATION THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE R