Resultant de la Proposition californienne 65, ce produit contient des produits chimiques dont l’etat de la Californie reconnait causer le cancer et des anomalies congenitales ou d’autre danger pour la reproduction. • 1 • General SAFETY PrecauTIONs 1. The following safety information is provided as a guideline to help you operate your new welder under the safest possible conditions. Any equipment that uses electrical power can be potentially dangerous to use when safety or safe handling instructi

FUME HAZARDS 1.5 WARNING: FUMES, GASES, AND VAPORS CAN CAUSE DISCOMFORT, ILLNESS, AND DEATH! To reduce risk of discomfort, illness, or death, read, understand, and follow the following safety instructions. In addition, make certain that anyone else that uses this welding equipment or is a bystander in the welding area, understands and follows these safety instructions as well. Do not weld in an area until it is checked for adequate ventilation as • described in ANSI standard #Z49.1. If ventilati

b. Delivery pressure continues to rise with down stream valve closed, c.) The gauge pointer does not move off the stop pin when pressurized or fails to return to the stop pin after pressure is released. HOT SLAG/MOLTEN METAL HAZARDS WARNING PLASMA ARC CUTTING CAN CAUSE SERIOUS BURNS FROM HOT SLAG OR MOLTEN METAL! To reduce risk of injury from serious burns caused by flying or dripping hot slag or molten metal, read understand and follow the following safety instructions. In addition, make certai

Until the final conclusions of the research are reached, you may wish to minimize your exposure to electromagnetic fields when welding or cutting. To reduce magnetic fields in the workplace: • Keep cables close together by twisting or taping them. • Arrange cables to one side and away from you. • Do not coil or drape cables around your body. • Keep cutting power source and cables as far away from you as practical. • Connect work clamp to workpiece as close to the cut as possible. About Pacemaker

Extension cord lengths longer than 25 feet will require heavier wire gauges to compensate for voltage losses. INSTALLING THE ELECTRODE HOLDER 2.6 Attach the electrode holder to the electrode cable according to the following steps. Remove the handle (3) from the electrode holder (1) by removing the 1. screw holding the handle (not shown) and sliding the handle off. Remove the screw (6) from the electrode holder (1). 2. Push the cable (4) through the handle (3). 3. Insert the screw (6) through the

07 9807600477 DRIVE BEARING ROLLER 10 9807600579 DRIVE TENSIONER KNOB 11 9807600580 DRIVE TENSION SPRING Reference Number Part Number Description 01 93537 93550 NOZZLE 3/8", TWECO STYLE 21-37 NOZZLE 1/2", TWECO STYLE 21-50 02 93524 93530 93535 .024 CONTACT TIPS, TWECO STYLE 11-23, PKG. OF 5 .030 CONTACT TIPS, TWECO STYLE 11-30, PKG. OF 5 .035 CONTACT TIPS, TWECO STYLE 11-35, PKG. OF 5 03 9807600581 GUN NECK 06 9807600520 GUN HANDLE ASSEMBLY WITH TRIGGER 12 9807600478 GAS VALVE 9807600516 LINER M

If possible, the work piece should be positioned so that the bead will run on a flat surface. Preparing The Joint For effective welding, the surfaces to be joined must be free of dirt, rust, scale, oil or paint. Welding on metals not properly cleaned will cause a brittle and porous weld. If the base metal pieces to be joined are thick or heavy, it may be necessary to bevel the edges, with a metal grinder, at the point of contact, as shown below. The angle of the bevel should be approximately 60

INSTRUCCIONES DE OPERACION AL USAR LAS ABRAZADERAS 3. DE CONEXION RAPIDA. Advertencia: El no seguir las instrucciones puede causardano o explosion. Lee el manual de instrucciones entero antes de usar. Enchufe el cable de la abrazadera en el Conector Rapido acoplado al 3.1 IP-180KE Apague la ignicion antes de conectar los cables.3.2 Asegurese de que el interruptor del Arrancador Inmediato se encuentre 3.3 en la posicion OFF (apagado) hasta que las pinzas esten conectadas a la bateria del vehiculo

(Para un sistema a tierra negative.)* 7. Conecte la pinza negra (-) a una parte sin pintar e inmovil del chasis o del bloque del motor. 8. Si se hace conexion invertida de las pinzas del IP-1875C, suena alarma audible. NO encienda la unidad. Esto podria causar grave dano. Invierta las conexiones, y el alarma deja de sonar. 9. Si no existe un sonido de alarma, encienda el Aparato y entonces arranque el motor. Si el motor no enciende, entre 5 y 8 segundos, detengase, expere 1 minuto antes de inten

Schumacher Electric Corporation Mount Prospect, IL 60056 U.S.A. Send Warranty Product Repairs to: Customer Service Returns P.O. Box 280, 1025 E. Thompson Hoopeston, IL 60942-0280 Questions? Call Customer Service: 1-800-621-5485 00-99-000666/0606 important safety INSTRUCTIONS save these instructions Before using your PI-140, read and understand this Owner’s Manual. • Keep the inverter well ventilated in order to properly disperse heat generated while it is in use. Make sure there are several inch