Tighten securely. BAGGER KIT INSTALLATION STEP 11: Install bumper mount standoffs onto rear bumper of machine, utilizing existing hardware on machine. NOTE: Invert hardware when installing standoffs, installing bolts out through bumper with nuts facing out. NOTE: When installing standoffs, be sure that the bumper mount plate mounting holes along the back bar of the standoffs are located towards the right side of the machine. Refer to the Parts List section of the manual. STEP 12: Install bumper

TWIN LINE TAP FEED HEAD KIT ITEM PART NO. DESCRIPTION _ 6-8037 KIT, .095 L.H. Twin Line Tap Feed Head (Includes Items 1 thru 7) 1 4-2081 HEAD, Twin Line Bump, L.H. (Includes Items 2 thru 6) 2 4-2073 ASSEMBLY, Hub 3 4-2074 SPRING 4 4-2082 ASSEMBLY, Spool & Line 5 2-1971 KNOB, Bump 6 4-2083 BOLT, Slotted Hex Flange, L.H. 7 1-8784 CARD/Parts (Not Illustrated) 1 5 Section I - TRIMMER ACCESSORIES BRUSH BLADE CONVERSION KIT WITH METAL SHIELD 16 Section I - TRIMMER ACCESSORIES BRUSH BLAD

N0.1690179 USED ON 36” TILLER 38” REVITALIZER PROTECT YOURSELF AND OTHERS A 1. Read and be familiar with the owners manual for your tractor and the owners manual for attachment before operating attachment. 2. Do not allow anyone to use tractor and attachment unless they have been instructed in how to operate it safely. 3. Never attempt to adjust, repair or service attachment while the tractor engine is running. 4. Do not allow others near attachment when it is operating. 5. Stay clear of

4.1 Set-Up Procedure — New Unit --------------------------------------------------------- 4.1 - 4.2 2 I-OPERATION & SERVICE INTRODUCTION: The information in section one is generally the same as that presented in the Snapper Operator's Manual. It is repeated here for general reference and adjustment purposes. RIGHT SIDE BLOWER CLUTCH HANDLE CONTROL PANEL FORWARD-REVERSE DIRECTIONAL CONTROL FUEL TANK FILLER CAP* (KEEP TIGHTENED) DISCHARGE DEFLECTOR CAP DISCHARGE CHUTE IMPELLER HOUSING

692211 Spring. Governor (Used Before Code Date 96052000). Used on Type No(s). 0120, 0121, 0123, 0125, 0126, 0127, 0128, 0131, 0140, 0147, 0148, 0150, 0151, 0166, 0167, 0197, 0312, 0313, 0314, 0317, 0319, 0320, 0325, 0353, 0358, 0362, 0366, 0367, 0370, 0371, 0373, 0379, 0380, 0383, 0388, 0390, 0392, 0393, 0394, 0396, 0397, 0398, 0399, 0401, 1144, 1305, 1315, 1316, 1318, 1350, 1351, 2222. 690252 Spring. Governor (Used After Code Date 96051900). Used on Type No(s). 0115, 0129, 0132, 0137, 0138, 013

This two-stage Thrower will do a great job of clearing snow from your drives and walks on the rear engine Rider which not only provides weight on the rear drive wheels for excellent traction but gives you good forward visibility. This manual covers the recommended procedures for operating the unit as a snow thrower plus detailed instructions for converting the Rider to and from the mower mode as the seasons change. Before operating in the snow thrower mode, be sure to read the important safety i

Refer to back page for kit information. CHARGING-ON UNIT. If the battery has insufficient energy to crank the engine for starting, rope start the engine and allow it to run at medium to fast speed to restore charge. CHARGING-AUTO TYPE CHARGER: If the battery charge cannot be restored by running the engine, it may be too deeply discharged to accept charge. In this event, disconnect and remove the battery from the unit and charge on an automotive type charger at LOW RATE only (2 amp maximum) for

Detach cable from receptacle and engine. On jump start equipped models, refer to instructins provided in kit. NOTE: If engine does not start after five seconds of continuous cranking, release electric start button to prevent overheating of the starting motor. Locate and correct cause of starting problem before repeating electric starting attempt. WARM-UP PERIOD: Allow brief warm-up outside with clutches released to avoid stalling cold engine. Reset Choke as instructed in Engine Manual as the u