26632750200 36832057200 99461050304 FRAME,HANDLE HANDLE,FRONT COLLAR,DAMPER B DAMPER,B WASHER,BRAKE SHAFT BOLT,HEX,5X30S 1 1 4 4 4 4 6-7 6-8 6-9 6-10 6-11 5053329020 0403316080 99051050403 99210050062 99201050061 CLIP SUPPORT,HANDLE BOLT,HEX,5X40 WASHER,S,5 WASHER,5 1 1 2 2 2 Page 7 custsvc@nikko-tanaka-usa.com PARTS INFORMATION THT-210S REAR HANDLE • FIGURE 7 ITEM PART NUMBER DESCRIPTION QTY COMMENTS 7-1 0513329020 HANDLE,B 1 7-2 0503329020 HANDLE,A 1 7-3 2303329020 LEVER,THROTTLE 1 7-4 2313329

Depth gauge 10. Correct angle on top plate (degree of angle depends on chain type) 11. Slightly protruding "hook" or point (curve on non-chisel chain) 12. Top of depth gauge at correct height below top plate 13. Front of depth gauge rounded off LOWERING DEPTH GAUGES WITH A FILE 1) If you sharpen your cutters with a file holder, check and lower the depth. 2) Check depth gauges every third sharpening. 3) Place depth gauge tool on cutter. If depth gauge projects, file it level with the top of the t

29) Install the chain and bar on the motor unit as follows: 1.Secure the chain around the motor unit’s sprocket. Ensure that its teeth correspond with the direction of rotation according to the arrow (A). 2. Position the bar and thread the chain around the bar. CAUTION! Ensure that the tip of the tension screw’s nut (B) fits into the hole on the bar. 3. Install the guide (C) and loosely tighten the two bar bolts (just so that there is no play on the bar). 4. Adjust the chain using the tension sc

SM 2055E TABLE OF CONTENTS Introduction ....................................... 3 Symbols ............................................. 4 Warning Signs ................................... 4 Safety Regulations ............................ 5 Description ........................................ 7 Installation ....................................... 16 Fuel Handling .................................. 21 Starting and Stopping.....................23 Use.................................................

Recommended max. speed: See the Technical data section. During the running-in period (8-10 tanks of fuel) the maximum speed should be set 600-700 rpm below the recommended maximum speed (= open the high speed jet H a further 1/8 turn). Conditions • Before any adjustments are made, make sure that the air filter is clean and the air filter cover is fitted. If you adjust the carburettor when the air filter is dirty it will result in a leaner mixture when the filter is finally cleaned. This can lead

If the high speed jet H is set too lean (screwed in too far) the engine speed will be too high and cause engine damage. Do not let the engine run at full speed for more than 10 seconds. Apply full throttle and turn the high speed jet H very slowly clockwise until the engine slows down. Then turn the high speed jet H very slowly anticlockwise until the engine starts to run unevenly. Now turn the high speed jet H slowly clockwise a little way until the engine runs smoothly. H Note that the engine

Both situations could cause serious injury. • Before moving your chain saw switch off the engine and lock the chain using the chain brake. Carry the chain saw with the bar and chain pointing backwards. Fit a guard to the bar before transporting the chain saw or carrying it for any distance. • Never put a chain saw down while the engine is running unless you have it in clear view and the chain brake is on. Switch the engine off before leaving your chain saw for any length of time. Basic cutting t

This results in damage to the oil pump, the bar and the chain. • It is important to use oil of the right grade (suitable viscosity range) to suit the air temperature. • In temperatures below 0°C (32°F) some oils become too viscous. This can overload the oil pump and result in damage to the oil pump components. • Contact your service agent when choosing chain oil. 26 – English FUEL HANDLING Fuelling ! WARNING! Taking the following precautions, will lessen the risk of fire: Do not smoke or place h

LT2115A PRODUCT NO. 960 11 01-82 401433 11.14.05 VB PRINTED IN THE U.S.A. REPAIR PARTS TRACTOR - MODEL NO. LT2115A (96011018200), PRODUCT NO. 960 11 01-82 SCHEMATIC 03054 (197428) BATTERY FUSE IGNITION SWITCH RED RED RED BLACK IGNITION UNIT HEADLIGHTS BLACK BLACK BLACK WHITE WHITE WHITE RED BLACK ORANGE BLACKBROWN BLACK BLACK BLACK STARTER M SEAT SWITCH (NOT OCCUPIED) GROUNDING CONNECTOR ATT'MENT CLUTCH (CLUTCH OFF) CLUTCH / BRAKE (PEDAL UP) SOLENOID BLACK A AMMETER RED G B S M A1 A2L HOUR METER

LT2113 PRODUCT NO. 960 11 02-66 4747 532 43 49-43 Rev. 1 TRACTOR - - MODEL NO. LT2113 (96011026604), PRODUCT NO. 960 11 02-66 DECALS 27 2727 3 10 9 15 12 11 19 10 7 2 4 1 14 8 5 5 6 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 532 19 68-41 Decal, Warning Engine Symbols 12 532 18 04-32 Decal, 100 Dba 2 532 14 50-05 Decal, Bat Dan/Poi P/L Symbols 14 532 41 79-26 Decal, Eng. HP 3 532 41 90-19 Decal, RPL. 15 532 15 97-37 Decal, Brake/Clutch 4 532 19 63-57 Decal, Deflector Warning Symb