Asegure los tornillos con arandelas planas M6 y tuercas hexagonales de 6 mm de diam. Ajuste bien. Ver Figura 2. 3. De vuelta el montante angular frontal y el panel inferior hacia abajo como muestra la figura 3. 4. Coloque las dos estructuras angulares laterales en el panel inferior de modo que las dos perforaciones para las abrazaderas del eje esten cercanas al montante angular frontal. Ver Figura 3 5. Asegure ambas abrazaderas del eje a las estructuras angulares laterales y al panel inferior us

Hopper Strap 9. Hopper Assembly Hardware Package (see page 3) 567149238 EFDCBAKLMGHIJNOQRSNOT SHOWN FULL SIZESHOWN FULL SIZEP REF. QTY. DESCRIPTION A 6 Hex Bolt, 1/4-20 x 2" B 2 Hex Bolts, 3/8-16 x 1-1/4" C 4 Hex Bolt, 1/4-20 x 1" D 1 Carriage Bolt, 1/4-20 x 3/4" E 10 Nylock Nuts, 1/4" F 2 Nylock Nuts, 3/8" G 6 Nylon Washer H 10 Flat Washer, 5/16" I 4 Flat Washers 1-5/8" J 1 Cotter Pin, 3/32" x 3/4" K 1 Cotter Pin, 1/8 x 1-1/2" L 1 Hair Cotter Pin, 1/8" M 1 Hitch Pin N 1 Short Spacer Tube O 1 Lo

FT. (SUPER 17) • Assembly • Operating •Maintenance •Repair Parts 303 WEST RAYMOND • SULLIVAN, ILLINOIS 61951 PRINTED IN U.S.A FORM NO. 46085 (Rev. 11/94) ASSEMBLY INSTRUCTIONS Contents of Hardware Pack (See figure 1) REF. QTY. DESCRIPTION A 2 Tube Spacer 1-1/4" O.D. x 2" Lg. B 2 Pin, Cotter 1/8 x 1-1/2” Long C 2 Hex Nut 3/8 Thread D 4 Washer, Flat 1.032 I.D. E 2 Hub Cap F 23 Hex Bolt 1/4 x 1/2" Long G 6 Hex Bolt 1/4 x 5/8" Long H 6 Hex Bolt 1/4- 3/4" Long I 2 Lock Washer 3/8" I.

Mantenga las herramientas con filo y limpias para obtener un mejor y mas seguro funcionamiento. Las empunaduras siempre deben mantenerse limpias, secas y libres de aceite o grasa. 11. Mantenga las manos, rostro y cuerpo lejos del tronco mientras se lo esta partiendo. 12. MANTENGASE ALERTA. Piense en lo que esta haciendo, haga uso del sentido comun. No ponga la herramienta en funcionamiento si se esta cansado. 13. VERIFIQUE LA PRESENCIA DE PIEZAS DANADAS. Antes de utilizar cualquier herramienta,

45-02181 26" LEAF/LAWNSWEEPER Safety Assembly Operating Maintenance Repair Parts CAUTION: Read Rules for Safe Operation and Instructions Carefully thefastest way to purchase parts PRINTED IN USA FORM NO. 40261 (4/24/07) SAFETY RULES Remember, any equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when using this equipment. CAUTION: VEHICLE BRAKING AND STABILITY MAY BE AFFECTED WITH THE ADDITION OF AN AC

The rate chart is calculated for light and heavy application. The faster you drive, the wider the broadcast width. A variation in speed will determine the flow rates and width of broadcast. CAUTION When broadcasting weed control fertilizers make sure broadcast pattern does not hit evergreen trees, flowers or shrubs. FIGURE 16 SPROCKET SHAFT AGITATOR WIRE 3/8" LOCKNUT AGITATOR SLEEVE FIGURE 17 5. Keep tires inflated to 15-20 P.S.I. Do not over inflate. FIGURE 18 xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

DESCRIPTION KEY QTY. DESCRIPTION A B C D E F G H I 6 2 2 1 8 2 2 4 8 Hex Bolt, 1/4-20 x 1-3/4" Hex Bolts, 3/8-16 x 1-1/4" Hex Bolt, 1/4-20 x 3/4" Carriage Bolt, 1/4-20 x 3/4" Hex Lock Nuts, 1/4-20 Thread Hex Lock Nuts, 3/8-16 Thread Lock Washers, 3/8" I.D Nylon Washer Flat Washer, 5/16" J K L M N O P Q R S 4 1 1 1 1 2 1 1 1 1 Flat Washers 1-5/8" Cotter Pin, 3/32" x 3/4" Cotter Pin, 1/8 x 1-1/2" Hair Cotter Pin, 1/8" Hitch Pin Spacers Nylon Wing Nut Adjustable Stop Flow Control Link Grip 3 5.Alig

3. Remove the lock nut from the middle bolt in the crossover tube and shaft support plate. Leave the bolt in place. See figure 2. 4. Assemble the short end of the hitch tube onto the middle bolt and secure it with the same nut you removed. DO NOT TIGHTEN YET. See figure 2. IMPORTANT: The hitch tube must attach to the side of the crossover tube opposite the shaft support plate. 5. Assemble the two hitch braces to the hitch tube using a 1/4" x 2" hex bolt and a 1/4" nylock nut. DO NOT TIGHTEN YET.

44483 (Rev. 4/90) RULES FOR SAFE OPERATIONS The following safety precautions are suggested. This broadcast spreader is designed, engineered and tested to offer reasonably safe and effective service, provided it is operated in strict accordance with these instructions. Failure to do so may result in personal injury. Always observe the rules of safe operation. 1. Do not allow anyone to operate the broadcast spreader without proper instructions. 2. Do not permit children to operate the broadcas

(Refer to figure 2 on page 4.) Use shim washers (Ref. no. 20 on pages 10 and 11) as needed for minimum backlash. Add grease to gear and sprocket. 2. If the agitator wire becomes damaged or worn it can be replaced. Loosen the 3/8" hex nut on top of the sprocket shaft until agitator wire is free. Remove old agitator wire from hole in agitator sleeve and replace with new agitator wire. Position agitator wire so that sprocket shaft turns freely, then tighten 3/8" hex nut on top of sprocket shaft. Se