IMPORTANTE: Quite la cinta adhesiva de transporte de los dos registros de tiro traseros ubicados en la abertura de escape. MATERIALES NECESARIOS (obtengalos localmente) SECADORAS DE GAS, ELECTRICAS O DE VAPOR • Un interruptor general con fusible o disyuntor. SECADORAS DE GAS SOLAMENTE • Una valvula de corte de gas para la linea de servicio de gas conectada a cada secadora. SECADORAS DE VAPOR SOLAMENTE • Una valvula de corte de vapor para la linea de servicio de vapor que se vaya a conectar aguas

(102 mm) 6 in. (152 mm) 7 in. (177.8 mm) 8 in. (203 mm) 10 in. (203 mm) 12 in. (305 mm) Table 4 9001000 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 45 Installation Water Connection WARNING To avoid personal injury, recommended inlet water temperature should be nohigher than 125° Fahrenheit (51° Celsius). W709 The 18-135 models are delivered with hoses with 3/4 inch hose connectors. The 165 model is delivered with 3 x 1 inch and 1 x 3/4 inch hose connectors. These hoses fi

Si el vapor vuelve a la caldera por gravedad, omita el purgador pero instale la valvula reguladora de vacio y la valvula de retencion en la linea de retorno cerca de la secadora. 7. Instale la union y la valvula de corte en la linea de retorno y efectue las conexiones finales de la tuberia a la tuberia principal de retorno. RECOMENDACIONES PARA COLOCACION DE TUBERIAS 1. Instale un purgador de condensado en cada serpentin individual. Mantenga siempre limpio el purgador de condensado y en buenas c

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70283501 11 Operation TMB2136N Figure 6 Dual Digital Timer Control RQ Control Suffix 1. Select HIGH, MED, LOW or NO HEAT by turning the temperature knob. 2. Set the HEAT TIME for the number of minutes (from 0-60) desired. 3. Set the COOL DOWN TIME for the number of minutes (from 0-15) desired. 4. Select reversing or nonreversing cylinder rotation setting, if applicable. 5. Press and release START button to start tumbler. Display

2. Check power circuit, supply voltage, fuses and disconnects. 3. Verify drive to motor wires are damage free, properly connected and torqued to specifications. 4. Check belt tension and condition. 5. Verify no mechanical problems exist (i.e., binding, motion restriction). 6. Check control input signals. Refer to applicable table of inputs. Problem: Drive started but wash basket is not rotating. Corrective Action 1. Verify drive to motor wires are damage-free, properly connected and torqued to s

Electric dryer is connected to a 208 volt circuit. Drying time will be 20% longer than drying on a 240 volt circuit. Drying procedures have not been followed. See Drying Procedures, page 4. Outside exhaust hood or exhaust duct may be clogged or restricted. Clean out any obstruction. High humidity. Use a dehumidifier near the dryer. Excessive wrinkling. Dryer is overloaded. Do not overload. See Drying Procedures, page 4. Items left in dryer too long. Remove items as soon as cycle ends. Insufficie

3 Nameplate Location.............................................................................. 4 General Inspection................................................................................ 5 Storage .................................................................................................. 5 PowerFlex 40 and 400 Drive Control Logic ..................................... 6 Installation/Wiring................................................................................ 6 Input

Programming supply 1, 2 or 3 ONLY activates water in compartment A, B or C. Programming supply 4 activates relay 1. Programming supply 5 on the WE-8 will activate supply relay 2, etc. Programming supply 4-9 on the WE-8 will activate supply relay 1-6 on the board, respectively. Refer to Table 8. SupplyRelay SupplyRelay SupplyRelay 3 4 5 * L1 (220 VAC) wire or terminal for remote liquid supply connection. ** L2 common wire (220 VAC) or terminal for remote liquid supply connection. Figure 36 CFS8N

U135ME3A COM X - fmr RL RM RH STR STF Drive Control Connections V-COMPUTER OUTPUT BOARD Figure 41 U136ME3A J8 J2A 30 31 32 33 34 35 J7A J3B J1 Ribbon Terminals 1 thru 16 Terminals 17 thru 29 Drive Control Connections U136ME3A WE-6 INTERFACE BOARD Figure 42 U148ME3A 1 7 6 12 H2 H4 H1 H3 H5 Drive Control Connections EDC OUTPUT BOARD Figure 43 F232120 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Allen-Bradley 1305-Series AC Drives Control Wire During troubleshooting, if the w

(1194 mm) 24.4 in. (620 mm) 30.8 in. (782 mm) CFS468N 12.9 in. (328 mm) 10.4 in. (264 mm) 36.75 in. (934 mm) 37.8 in. (960 mm) 6.1 in. (155 mm) 35 in. (889 mm) 39.4 in. (1001 mm) 4.4 in. (112 mm) 15.5 in. (394 mm) 5 20 in. (508 mm) 38 in. (965 mm) 41 in. (1041 mm) 3.5 in. (89 mm) 1 3 2 4 8 7 9 10 6 25.16 in. (639 mm) 30.31 in. (770 mm) 8 in. (203 mm) 35 Pound Capacity Models with U in the 8th Position (e.g. *X35PVXU6) 46.3 in. (1176 mm) Figure 6 9001000 © Copyright, Alliance Laundry Systems LLC