Do not defeat the safety purpose of the polarized plug. 13) Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 2 Notes: OO Specifications: typical @ 25 C ± 5 C 5515 Modulator Inputs video 1Vp- p@75 audio 1 V rms @ 47k L & R inputs combined for monaural performance Video differe

Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, e) If the product has been dropped or damaged in any way, and f ) When the product exhibits a distinct change in performance - this indicates a need for service. 22) Replacement Parts - When re placement parts are required, be sure the service techn

Some states do not allow limitations on how long the implied warranty lasts or the exclusion or limitation or incidental or consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may have other rights which may vary from state to state. PERFORMANCE MULTI-ROOM VIDEO Modulator Installation Manual select program IR pll frequency control ABC D model 5545 quad digital modulator with ir output TM Frequency-Agile Multi

The channel injector designed to mount indoors or outdoors close or antenna feed. The system uses the existing in the house. The CatCam was designed to work with Cat 5 wiring. system will function with quad wire, Cat 5 delivers the picture. The Cat 5 allows the use of an automatic line length and picture compensator. Quad wire does not take advantage of this enhancement. Model Differences: The model 9500HHR series is a high headroom design for CATV and off air antenna feeds only. (5-806MHz) The

Channel At the channel connect Cat color coding on blue/white pin 1 © 1999 When using only quad wire use positions 1, 2, 5 and 6 and follow color coding. green pin 1 run the Cat 5 wire through the grommet at the bottom of the injector Applying Power and Programming Step Three The 9500 series has three different methods for applying to the system. Use only one method for applying power. Method One: Apply power directly to the channel injector with the power supply. power supply Power plug © 1999

Before Out to TVs Incoming CATV or antenna coax Now attach the supplied coax jumper back to the existing splitter and tighten all connections with a 7/16” wrench. After Mount the injector within 4” of the splitter Supplied coax jumper goes back to splitter Out Incoming CATV or to TVs antenna coax © 1999 Installation The camera wire from the shown. prepare the Cat 5 wires stripping 1” of outer sheath and 1/8” of insulation insert the 6-32 screws into frame and bottom holes of gang box gasketframe

default for the 9500 series. However, if the cable services uses HRC or the TV appears to search for the “created channel”, channel injector for HRC. For HRC enter 98. Reset to IRC by entering 99. Entries 98 and 99 are for setting HRC or IRC only. They will not change the channel number. With programming complete, test each TV in the system to see that it is receiving the new channel. How to Determine which source on and one unused channel avoid interference. channels and appear © 1999 Upper rig

Second, install the camera at the desired location and run Cat 5 wire from the camera to the channel location. Third, apply power and select an unused channel for the CatCam picture to appear on all the televisions. WARRANTY Multiplex Technology, Inc. warrants this defects in materials and the date of purchase or or at its option, replace defective product. To obtain warranty service, material authorization (RMA) to Multiplex Technology, Inc., 3001 Enterprise Street, Brea, 92821, Attention: Cust

Before Out to TVs Incoming CATV or antenna coax Now attach the supplied coax jumper back to the existing splitter and tighten all connections with a 7/16” wrench. After Mount the injector within 4” of the splitter Supplied coax jumper goes back to splitter © 1999 Out Incoming CATV or to TVs antenna coax Installation Step Two The wall plate Run a line of Cat and connect wires note: When using quad wire connect wires only to pins 1, 2, 5 and 6. Leave the resistor in place at pins 3 and 4. At the c

warrants this product free from defects in materials period of one year from the date repair, or at its option, replace the defective obtain warranty service, call MTI for authorization (RMA) number and return Attention: Customer Service. Please put the RMA number on the outside Any implied warranty arising from the sale of the product including implied warranties of merchantability and fitness for purpose are limited to the warranty stated above. MTI shall not be responsible for losses or damag