123.24201 User’s Manual and Maintenance Guide Questions? Please call 1-800-422-3865 DO NOT RETURN TO THE STORE Call 8:00 a.m. to 6:00 p.m. Monday through Friday (Central Standard Time) Store this manual in the glove compartment of your tow vehicle. Warning: For safe operation of this trailer, be sure to read all instructions and warnings. Failure to follow instructions and warnings could result in property damage, serious injury and death. (text) Instruction No. 1028859 D 10/26/2007 (Watermark)
If you need assistance, call 1-800-235-5878. SPECIAL NOTICE: Exposure to vibrations through prolonged use of gaso line powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnor mal swellings. Prolonged use in cold weather has been linked to blood ves sel damage in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fing
6. Locate the Door Control within sight of the door at a minimum height of 5 feet where small children cannot reach and away from all moving parts of the door. 7. Install the User Safety Instruction Label on the wall adjacent to the door control and the Maintenance Instruction Label in a prominent location on the inside of the garage door. 8. Upon completion of the installation, the door must reverse when it comes in contact with a one-inch high object or a 2x4 laid flat on the floor. 9. Do not
accessible brushes --should be performed by a Proceed as follows when replacement is required:. qualified service technician at a Sears store to • Unplug your saw. avoid risk of personal injury. & WARNING: Failure to unplug your saw could BRUSH REPLACEMENT result in accidental starting causing serious See Figure 36. injury. • Remove brush cap with a screwdriver. Brush assembly is spring loaded and will pop out when you remove brush cap. • Remove brush assembly. BRUSH • Check for wear. If worn, a
1 11 CRRFTSMRN"TABLESAW315.228110 The following tools are needed for assembly and alignment. Note: The four hex keys listed below have been provided with your saw. The remaining tools are typical shop tools and are not included with your saw. 3/8 in. NUT DRIVER FRAMING SQUARE 'U'l'O'l'l'l'l'l,U,l,l,l,l,t, ,_rl,g,f,v,l,l,l,l,l,l,l,U,l,f. .t.l,',l,*.l.,.l,L,J.l,l.,.I,*,l.*,l,,,I.,,I,_.l.,,I.i SOCKETWRENCH WITH7/16in.SOCKET ADJUSTABLE WRENCH SCREWDRIVER #2 PHILLIPS SCREWDRIVER FLATBLADE I_ COMBINAT
2. Press and hold the release button (Fig.12). 3. While firmly holding the upper shaft housing, pull the cutting attachment or add-on straight out of the coupler (Fig.12). Coupler Release Button Fig. 12 WARNING: To avoid serious injury and damage to the unit, shut off the unit before removing or installing attachments. STARTING INSTRUCTIONS 1. Check the oil level in the crankcase. Refer to Checking the Oil Level ( p.] 2). 2. Turn switch to ON position (Fig.] 4). NOTE: If your unit is equipped wi
• Allow the engine to cool before storing or transporting. Be sure to secure the unit while transporting. • Store the unit in a dry area, locked up or up high to prevent unauthorized use or damage, out of the reach of children. • Never douse or squirt the unit with water or any other liquid. Keep handles dry, clean and free from debris. Clean after each use, see Cleaning and Storage instructions. (p.19) • Keep these instructions. Refer to them often and use them to instruct other users. If you l
Cubierta Trasera NOTA: En este manual, "izquierda" y "derecha" se refieren seg#n come se vea desde la posicidn de operacidn. GARANT|A COMPLETA DE FABRICACION Cuando se opera y mantiene de acuerdo con todas las instrucciones que se proporcionan, si alguna pieza no ampliable de este equipo falla debido a un defecto en los materiales o en la fabricaci6n dentro de dos a_os desde la fecha de compra, Ilame a 1-800-659-5917 para solicitar una reparaci6n gratuita en su hogar. La cubierta y el eje delant
** Verifique el funcionamiento del sistema de seguridad cuando la unidad haya estado almacenada por 30 dias o un peHodo mayor. 1-Estos servicios deber&n ser efectuados por Sears u otro taller de servicio calificado. 6O Elementos de Mantenimiento del Tractor A ADVERTENCIA Mueva las palancas de velocidad de desplazamiento a las posiciones ARRANCAR/ESTACIONAR, engrane el freno de estacionamiento, APAGUE las cuchillas del cortacdsped, APAGUE el interruptor de ignici6n, y espere que todas las piezas
Apriete los pernos de montaje (D). Para Ajustar la Brecha Final de las Palancas de Control: La brecha final de las palancas de control deben ajustarse de modo que las palancas no se toquen entre si cuando se pongan en posicion de DRIVE. Afloje la contratuerca (A, Figura 32) y ajuste la longitud del tornillo de cabeza redonda (B) de modo que las palancas no se toquen entre si. Repita lo mismo en el lado opuesto. Apriete la contratuerca (A) para fijar el tornillo de cabeza redonda en su posicion.