5. Icemaker related problem. 6. Faulty or disconnected wiring. 1. Check switch and replace if necessary. 2. Check switch and replace if necessary. 3. Replace bin thermostat. 4. Replace transformer. 5. Refer to Icemaker Operation and Service Manual for diagnosing. 6. Check for power and bin signal on icemaker PC board. 15 Symptom Carbonator pump not turning on. Carbonator pump is not turning off. Carbonation system is not carbonating. Carbonation system is producing excessively carbonated beverag

Before calling for service: • Check that there is ice in dispenser bin area • Check that all switches and circuit breakers are on • Check that congealed cubes are not causing a jam • Check that all drains are clear Symptom Possible causeSolution1. Does not dispense ice a. Faulty dispense gate b. Faulty dispense solenoid c. Power switch off or faulty d. Faulty dispense switch e. Wheel motor malfunction f. Drive chain off g. Sprocket key missing a. Replace dispense gate b. Replace dispense solenoi

Note: A 15% restocking charge will be deducted from the credit. If the cost to return the product to stock exceeds 15%, the actual cost will be deducted. 2 Table of contents Before you begin 4 Specifications 5 Field wiring 6 Installation 8 Installing freestanding dispensers 8 Installing wall mount dispensers 10 Installing Satellite-fill™ icemakers 12 Installing top mount icemakers 12 User information 14 Cleaning and sanitizing procedures 14 Service Information 16 Wiring diagram – lever models 16

Apply a thick bead, approximately. 1/4" (6mm) diameter, of NSF listed silicone sealant (Dow- Corning RTV-732 or equivalent) 1/4" (6mm) inside marked outline of dispenser. 11. Carefully position dispenser on counter. 12. Remove four screws securing splash panel to front of dispenser and gently lay splash panel on counter. (Water line to solenoid valve can be disconnected from water inlet valve by pushing on ring at end of inlet fitting while pulling on tubing.) 13. Secure dispenser to counter wit

Replace splash panel. 14. Plug dispenser power cord into 20 amp rated NEMA 5-20 wall socket. 15. If dispenser is equipped with SensorSAFE remove protective plastic coating form dispense sensor labels. 16. Turn on power and bin signal rocker switches and test operation. 17. Clean and sanitize icemaker following instructions in icemaker manual. 18. Remove dispenser hopper access lid and clean and sanitize dispenser according to instructions on page 14. 19. Replace front cover and secure with screw

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Before you begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Electrical requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Plumbing and clearance requirements. . . .. . . .. . . . . . . . . . . . . . . . .4 Field wiring diagrams. . . . .

Check dispenser and icemaker operation. 16. Sanitize icemaker according to instructions in icemaker manual. Discard ice made during sanitizing process. 17. Turn off icemaker bin signal switch. 18. Remove dispenser hopper lid; clean and sanitize dispenser according to instructions beginning on page 16. 19. Turn icemaker bin signal switch on and replace front covers, securing with screws. 8 Installing countertop dispensers ! Dispensers with top mount icemakers cannot be mounted on legs.They must b

13. Remove icemaker top panel and Fig. 8 louvered side panel. 14. Insert ice transport tube to a 1/2" (13mm) depth through mounting bracket (Fig 8 and 9.1) and secure transport tube away from condenser fan under float reservoir bracket (Fig. 9.2). 15. Tighten clamp screw(s) on icemaker base securely (Fig. 9.3). 16. Uncoil capillary tube from bin thermostat and route through hole in gasket to mounting bracket and secure as shown (Fig. 8). 17. Reinstall icemaker louvered side panel and top panel.

7 and 8) using wall bracket as template. 5. Lift dispenser onto wall bracket, positioning unit so that hook on back of dispenser is captured by wall bracket support angle (Fig. 6, hook detail). ! Do not rest dispenser weight on bottom front edge of wall bracket. 6. Install four 1/4-20 screws through bottom of wall bracket into bottom of dispenser to secure dispenser to bracket. 7. Remove splash panel. Water line to solenoid valve can be disconnected from water inlet valve by pushing on ring at e

Stainless steel frame and exterior with plastic trim. Up to 50 lbs (23kg) storage. Produces approximately 400 lbs (181kg) of Chewblet compressed nugget ice in a 24-hour period. Convenient, sanitary, user-friendly dispensing • Labor-saving, sanitary automatic load • Lever dispensing standard • Quick shut-off reduces the amount of wasted ice • High-quality Chewblet compressed nugget ice is slow melting, easy to chew • Clear chute ensures sanitary delivery and focuses ice cleanly into cups, pitcher