The P.C. Board causes the motor to run in a forward direction when the "ON” Switch is actuated and turn off when the "OFF/REVERSE" is momentarily depressed. When the "OFF/REVERSE" Switch is held down PCB1 reverses direction of the motor. If the motor stops due to a jam, PCB1 will reverse the direction of the motor then shut off after the jam has been ejected. When the "ON" button is depressed, contacts A and B of SI close momentarily completing a circuit between PCB1-1 and PCB1-3. At this time

Handle carriers carefully so they may be re-used. 3. insert the folded edge of the carrier STRAIGHT into the front of the laminator until you feel the rollers grab the carrier. 4. Remove the carrier from the rear of the GBC DocuSeal 120 after it has stopped moving. Leave the pouch within the carrier for a few seconds to cool before removing it. Removing it too soon may distort the lamination. 5. When you are finished laminating for the day switch the machine to “OFF”. ELECTRICAL SAFEGUARDS

Because the direction of the current path has been reversed by releasing the "ON" push button, the motor will immediately start to run in reverse. B4 5.0 TROUBLESHOOTING (Continued) 5.1.1 Electrical Operation (Continued) When the "OFF / REV" push button is depressed, switch contacts F3 - E3 are opened to deactivate the relay and turn the shredder off. If this push button is depressed when the shredder is turned off, contacts F4 - E4 are closed and power is supplied to the motor. The motor wi

The shredding of other metal items will damage the cutting blades. Plastic materials such as charge cards, covers, inserts and film may be shredded on a very limited basis However, extended shredding of such materials will prematurely dull the cutting blades The shredder control panel is shown in Figure 4-1. To start shredding, press the "ON" button then feed the material to be shredded into the throat of the shredder. Never exceed the maximum capacity of the shredder To tum the shredder off pr

LAS SIGUIENTES PRECAUCIONES DEBEN SER TENIDAS EN CUENTA PARA LA PUESTA EN MARCHA DE LA MAQUINA Y LA UTILIZACION DE .ESTA. PRECAUCIONES GENERALES • Usar la plastificadora solo para plastificar documentos en base a las especificaciones indicadas. • No inserir objetos en la maquina que no sean los documentos para plastificar. • Colocar la maquina en un lugar estable y seguro para prevenir la caida y los consiguientes danos para las personas y la maquina. • Apagar la maquina (off) cuando no va a ser

The GBC Shredmaster 2230S/2250X shredders are designed for small offices and low volume requirements. Innovative engineering has provided these shredders with the following operating and safety features: 1. Automatic Operation - The unit begins to operate when paper actuates the trigger in the shredder throat area. The motor stops running when the paper has cleared the cutting head and after the shredder has timed out. 2. Overload Warning - Whenever the capacity of the shredder is exceeded th

Remove 4 book supports from storage compartment, lb. Insert support #1 firmly in front slot. Firmly insert remaining supports in consecutive numerical order. 2a. Plug in and switch on 250T. The yellow wait light will illuminate. 2b. In about 4 minutes a "beep" will sound and the green light will iluminate. At this time the 250T is ready for binding. BOOK PREPARATION 3. Firmly hold sheets to be bound and place binding edge on lined surface. The first horizontal line above the paper will indic

The heat shoes can reach temperatures in excess of 300°F. • Keep hands and fingers away from the path of the sharp film cutter blade located at the film exit. • Do not place the laminator on an unstable cart, stand or table. An unstable surface may cause the laminator to fall resulting in serious bodily injury. Avoid quick stops, excessive force and uneven floor surfaces when moving the laminator on a cart or stand. »Do not defeat or remove electrical and mechanical safety equipment such as i

GBC se reserve le droit d’apporter des modifications a cette publication et aux produits qui y sont decrits sans preavis. Toutes les specifications et l’information au sujet des produits sont sujettes a changements sans preavis. Toute reference a l’information ou aux produits proteges par un droit d’auteur ou un brevet presentee dans ce document ne porte aucune licence sous les droits de GBC ou d’autres parties. GBC n’assume aucune responsabilite decoulant de contraventions aux brevets ou a tout

Para destruir disco compacto o de dvd (solamente para destruc toras de tipo corte recto), introducir el disco en el centro de la ranura de alimentacion. Cuando el disco ha activado el interruptor automatico de destruccion, la destructora entrara en marcha y se apagara cuando el disco este destruido. COMPARTIMIENTO LLENO Para prevenir que los desperdicios regresen a los cortadores y atasquen su destructora, esta unidad cuenta con un dispositivo automatico que apaga la destructora cuando el compar