(Maximum 3/4” (19mm) thick). 1. Remove wiring compartment cover at end of heater where power supply cable is to enter. Determine desired mounting location (Figure 2), position heater to wall as intended and mark wall (or floor) at location where power supply is to enter heater. Figure. 2 2 2. Drill hole entry. Install location as approximately for connections. 3. If any other heater, refer accessory 4. Wireway - a. The wireway commercial baseboard heaters. vidual through rent loads. b. To gain r

(Fig. 10.) Install grommet in bracket (Fig. 10) and attach on each end of fan, using two of the short screws provided. Position fan over opening so that grommets are resting against center joist. Attach fan and brackets to center joist with the two long wood screws and flat washers. Do not crush grommet when tightening screws. FIG. 10 FIG. 11 GROMMET BRACKET GASKET STEP 6 - Attach side panels to fan as shown using remaining short screws and washers. (See Fig. 11.) Bottom panels should rest upon

Wire Size Circuit Breaker or Fuse Size (Copper) 0 thru 12 #14 15 amp 12.1 thru 16 #12 20 amp 16.1 thru 24 #10 30 amp NET VOLUMES OF WIRING COMPARTMENT DESCRIPTION CUBIC INCHES CUBIC CENTIMETERS Heater Only (Each Wiring Compartment) 14.96 241 Heater W/SP Thermostat 11.18 180 Heater W/DP Thermostat 11.18 180 Heater W/Heat-Cool Switch Receptacle 9.51 153 Heater W/Duplex Receptacle 11.18 180 Heater W/DP Disconnect Switch 11.18 180 Heater W/Power Relay 10.76 174 Heater W/Transformer Relay 2.93 47 Thi

C. CAUTION: Incorrect wiring can cause motor failure and possible fire. Marley Engineered Products will not accept liability for damage resulting from incorrect wiring. FOLLOW ALL WIRING DIAGRAMS AND ALL INSTRUCTIONS CAREFULLY. D. This fan is designed to run on 120 volt A.C., 60 Hz power only. STEP 2 - The 3-speed control packed with this fan is used to operate fan from a remote wall location. Generally the best location is in the hallway near the fan. The control should be in sight of the fan.

STEP 7—Stand assembly upright with motor at top and position shutter on outside of frame. Secure shutter with (8) wood or lag screws (number 12 x 1” preferred) through holes in shutter frame. See Fig. 3. STEP 8—To mount this attic fan in gable or wall, a box must be framed into wall construction as shown in Fig. 4. See wall opening in chart. FAN SIZE “A” & “B” DIMENSIONS WALL OPENING SIZE 30” 33 3/4” x 33 3/4” 34” x 34” 36” 39 3/4” x 39 3/4” 40” x 40” STEP 9—Insert frame containing fan and shutt

Cuando no esta en uso, siempre desenchufe el cordon y envuelvalo alrededor del mango del calentador. Para almacenar mueva el calentador a una ubicacion segura. SERVICIO Este calentador no requiere ningun mantenimiento de rutina ademas de una limpieza ocasional para prevenir el taponamiento de la abertura de la rejilla de toma. Para limpiar la rejilla de toma de aire, use una aspiradora con el aditamento de cepillo o aire comprimido. El motor esta permanentemente lubricado. No opere el calentador

Todos los reclamos de trabajo de garantia deben estar acompana- dos por prueba de la fecha de instalacion. El cliente sera responsable por todos los costos incurridos en la extrac- cion o reinstalacion de los productos, incluyendo costos de mano de obra, y costos de transporte incurridos al retornar los productos a Marley Engineered Products Service Center y nosotros las repararemos o reemplazaremos, a nuestra opcion, sin cargo para usted, con transporte de regreso pagado por Marley. Se acuerda

PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. Figure 1 Description Leading Edge air curtains produce a wall of continuously flowing air that acts as a thermal barrier against outside air and flying insects. These air curtains maintain interior conditioned temperature and prevent heated or cooled air from escaping through open doorways. They redu

ADVERTENCIA GENERAL Antes de operar el calentador, asegurese que el tomacorrientes sea de la configuracion y capacidad apropiada para el calentador. Vea la configuracion del tomacorrientes en la primera pagina del manual.Nigun adaptador esta disponible para esta configuracio de hoja y no se debera usar ninguno. El tipo de enchufe es de 240 voltios con toma a tierra. Cuando se instala apropiadamente, proporciona una econexion a tierra a traves del cordon del calentador para proteger al operador c

It allows placement of the ventilator over the kitchen range and is operated by a wall switch away from the cooking area. Care must be taken at all times in handling the motor blade assembly, so as to avoid bending the blades. Model 898L is used for installation in frame houses. IMPORTANT SAFETY INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Do not use this fan with any Solid-State speed control device. 2. Use this unit only in