17 GUIDE FABRIC THREAD NEEDLE Length ofstitches Indicaof Pressure of tension \ Fabric Thread Needle presser foot ST. ZZ. Pressure Stitch length \ \ regulation a \o It Nylon 80 Cotton Light Tricot 605. Fibe 11 0.5-3 0.5-3 \\\ Silk 50 silk 50S.Fibe Wool silk Silk 11 Medium 60-80 Gingham Cotton 0.5-4 0.5—4 or E1hinJerse6QSFibe 5 14 Gabardine 50 Silk Heavy Denim 50 cotton 14 1—4 0.5—5 ‘\\ Jersey 50 S. Fibei 14 Tweed 50 Silk 14 As a general rule use shorter stitch lengths on finer fabrics and longer

(Refer to page 15 for dial setting). ZIGZAG SEWING Pattern selector position .Satin stitching can be used for sewing initials, patterns, applique, etc. -19 — BLIND STITCH 1. Fold fabric as shown. 2. To finish seam as shown. -20- Adjust width and needle position to obtain correct seam. Needle is not piercing edge of fold at all. x_ (A) Needle is pierces edge of fold too much. (B) Correct seam BUTTON SEWING (Use darning plate see page 11) 1. Lower drop feed. 2. Use button presse

Thread. Needle table Sewing (pattern selector) and operation table 16 To start sewing 17 To finish seam 18 19 Straight stitch 19 Zigzag sewing Overcasting Stretch stitch 20 Blind stitch 21 & 22 23 Button sewing 23 Binding Zippersewing 24 Button hole sewing Hemming 26 Twin Needle 27 27 Embroidery 28 Quilter 28 Seam guide 29 Maintenance (Cle.3ning and oiling) Checking Performance Problems WHAT TO DO NAME OF PARTS (FRONT VIEW) Pattern selector dial 7 Spool pins Take up lever 8 Top cover Thread tens

14. Desconecte Ia maquina de coser al hacer cualquier ajuste en el area de Ia aguja, como at enhebrar Ia aguja, cambar Ia aguja, enhebrar Ia bobina o at cambiar el prensatelas, etc. 15. Siempre desconecte Ia maquina de coser del tomacorriente at quitar las cubiertas, at lubricar o a! hacer cualquier otro ajuste de servicio mencionado en el manual de instrucciones. GUARDE ESTASINSTRUCCIONES CONTENTS 5-6 Name of parts 7 Accessories 8 Before sewing (Power supply and sewing lamp) 9 Removing extensio

of this appliance. Bed Plate. The Serial No. is located Ofl The Model No. is located on Rating Plate. Serial No. Model No. Retain these numbers for future reference. IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be folowed, including the following: - Read all instructions before usiAg (this appliance) DANGER To reduce the risk of electric shock: An appliance should never be left unattended when plugged in. Always unplug this appliance fr

Raise needle to its highestposition and open the 2. Open hinged latch of shuttle race Cover, bobbin case and pull bob bin case out of machine. 3. Release the latch and bob bin will fall out easily. INSERTING BOBBIN INTO BOBBIN CASE H 5 cm 1. Pull off 5cm of thread from bobbin and insert it 2. Guide the end of thread into bobbin case as shown. into slot. TenionsPrin Pull into iocm slot and under tension Spring and drawout about 10 cm ofthread, —7-— INSERTING BOBBIN CASE INTO SHUTTLE RACE Th Inser

Press foot release lever to remove foot. 3. Place presser foot below presser foot holder so that the presser foot pin is aligned with the slit in the presser foot holder. 4. Lower the presser foot so that the presser foot holder snaps onto the foot. 19 MACHINE SETTING CHART 1. STITCH INDICATOR 2. LENGTH DIAL 3. STITCH WIDTH DIAL 4.STITCH SELECTOR DIAL 20 f.............. STITCH 1. INDICATOR 2. STITCH LENGTH CONTROL 3. STITCH WIDTH CON- TROL \ 4. PRESSER FOOT t a ; 1 - 4 M A, B L.

No utilice nunca Ia maquina de coser si su cable o enchufe tienen defectos, si flO funciona correctamente, si manual. ha caIdo o estropeada, 0 Si se ha dejado caer en el agua. Lleve Ia maquina al vendedor autorizado o al servicio de reparaciOn mas cercano para que Ia examinen, reparen o efectuen los ajustes electricos o mecanicos neceSarios. 4. No utilice nunca Ia maquina de coser cuando tenga un orificio de ventilaciOn obstruido. Mantenga los orificios de ventilacion de Ia maquina y del mando d

3- 3. BEFORE SEWING in in Detachable Extension Table is a is lid it Changing Needle Set needle in the highestposition by turning handwheeltowards you. Loosen needle clamp screw andremove needle. With flat face away from you, insert a new needle into grooveof needle bar. Push needle until it reachesstopper a and tighten needle clamp screw firmly. Always use a straight needle with Proper needle a sharp point. straight shaft sharp point Using defective or worn needles not only causes stitch skippin

LotIon iD 50 SIC 80 90 1 14 lil Terv’ flZ4\/y l)ninr Di 30 ra:y CCPOs 100 ‘6 XTRA H1-AVY ipholslery Canvas \Wfl eq 30 Heavy Duty C C Poly ‘20 19 KM ES ,HT V’[lGHf lit Tricot Sl ylee 7) 9 lt 1FDlUM WEIGHT Si’k Light lersev Deible Knit 80 Nylon 70 80 11) 10 Medurr ‘ow” Nt C C Pot, Bat dAvy VVEICHT :1! P’,yer Ne’ D’J-’ NO 51k N,lio C C Poly 130 0 1 1 14 Med en ‘o Hea ‘tKE FURS VEolURS C’CPoly 30 ‘00 14 16 Bsll or ATHER JINYC S ElI MS 30 C C Poly 90 14 Wedqe ll,HT TO It El U H T MCD llM 30 C C Puly