128-5044 PRE-INSTALLATION: 1. Check and be certain that when the sliding door is fully closed the distance between the door and the jam is no greater then 1/2". This will insure proper contact when the switch is installed. NEW: Included with this kit are two 10° angled plates. These are intended for use in vans where the door meets the post at an angle, (Some Chrysler, Ford, and Chevrolet Mini Vans). The plate(s) are to be installed on the spring contact side between the gasket and spring con

When the alarm is allowed to arm passively, at the end of the 30 second arming cycle, the doors will notwill notwill notwill notwill not automatically lock. The system is shipped in the active door lock mode, therefore, no modifications are required for this feature. When passive door lock is selected, when the system is allowed to arm passively, at the end of the 30 second arming cycle, the doors willwillwillwillwill automatically lock. To program this feature, move dip switch number 1 to the o

See Diode Installation Instructions(page 5) after completing steps 1 through 10 below. Note:Electrical work must be in accordance with national and local electrical codes. If in doubt, consult a qualified electrician. 1. Verify transformer power rating. Power must be supplied from a 16 Volt AC, 10 Watt or a 16 Volt AC, 15 Watt transformer. 2. Remove cover from existing chime. 3. Labelallwiresbeforedisconnecting.Usingmaskingtape,mark each wire according to existing chime terminal markings. • “F”

The door reed switch Input is used to time out the timer when door is moved for Anti-Tailgating. The touch panel keypad is a new generation version of keypad with twelve sense buttons. It offers a key beep function with back light in order to provide its users with ease of use in the dark. Logical memory can prevents unauthorized persons from gaining PIN code entry by trial and error, The system will shut down for 60 seconds while 32 codes of incorrectly Master Codes enrolled or PIN codes attem

The door reed switch Input is used to time out the timer when door is moved for anti-tailgating. It's designed to mount on ANSI standard-single-gang electric wall box or on the surface of an interior or exterior wall. Logical memory can prevents unauthorized persons from gaining PIN code entry by trial and error, The system will shut down for 60 seconds while 30 codes of incorrectly Master Codes enrolled or PIN codes attempted ) None beeper signal of keypad activations(. Metal die casting housi

It may connects to another reader and serve as a controller. DG-600H enables the beeper to go off whenever the keypad is pressed. A tamper switch is used to protect the reader from external damage by linking the relay to the alarming system. This model communicates in Wiegand protocol and has a set of 600 proximity cards set to 26~37-bit or 26-bit. (For DG-600E, proximity cards are set to either 26 or 44 bit.) It takes the reader 0.5 seconds at most to read a proximity card or 5-digit PIN code.

. Output (free voltage contact), 3A@ 125Vac or 30Vdc ♦ Case Material: ABS (UL94V0) ♦ Operating Temperature:-20~+70°C ♦ Ambient Humidity:0~95% relative humidity noncondensing ♦ Visual Signals: ■ Green: Power on ■ Red: Relay activated ■ Yellow: Program Mode ' Lock-out ♦ Factory Master Code: 1234 ♦ Invalid PIN Lockout: System will shut down 60 seconds while 6 times of incorrectly password attempted. ♦ Relay Activation Time: (*20) ■ Pulse mode : 1~99 seconds (01~99) ■ Latching mode (00)

Digital code-operated (anti-tamper) for indoor access control keypad with up to 150 individual user PIN codes or 100 individual user cards and 50 user PIN codes, suitable for small and medium-size businesses, multi-tenant residential and commercial buildings, as well as clinics and health facilities. The door reed switch is used to time out the timer when door is moved. User access PINs ensure that all functions controlled to authorized persons only. It mounts to any standard single gang electri

Back Light keypads visible in the dark which you won't have trouble locating the control panel in the dark room. Upgrade the quality of Access Control System with the new updated design. DG-15LD j Features I 4 or 5 digit codes programmable I Allows up to 20+1 PIN codes I Dual Relays output for multi-control I Door Reed Switch Input for Anti-Trailing ■ Fully Programmable via keypad and master code ■ 3 LED display with Audible indication | Invalid PIN Lock-out ■ Metal casing housing With Va