II.B, 98/37/EEC) cannot be operated before the machine in which is assembled, will be declared in conformity with safety requirements according to 98/37/EEC norms and amendments. Orebro, Sweden, 01/03/2007 Stefan Ring Manager Quality & Environment Index 1.0 Introduction ...................................................................................................... 3 2.0 Symbols ...................................................................................................... 3 3.0 Saf

If the furnace is equipped with NOx screens and is to be 7. To measure total static pressure, add supply duct pressure detailed information. used with LP (propane) gas, the screens must be removed to the return duct pressure, add pressure drop across the ‘A’ prior to start-up. coil, and add pressure drop across the filter. Ignore negative 2. Drip leg in the gas line must be installed. signs on the readings. 3. The furnace controls require correct polarity on the power 8. Inlet gas pressure shoul

Slow Amber Flash - Normal operation with call for cooling. Two Amber Flashes - Normal operation with call for heat. Three Amber Flashes - Normal operation, burner is on at end of thermostat cycle. Six Amber Flashes - Normal operation with call for heat pump heating. Any Red Flash - Fault condition. NOTE: 4 or 5 flashes may indi cate a blown fuse on the circuit board. Application Upflow Downflow Horizontal Top 1" 0" 0" Vent 0" 0" 0" Rear 0" 0" 0" Side 0" 0" 1" Front* 0" 0" 0" Floor Combustible Co

Slow Amber Flash - Normal operation with call for cooling. Two Amber Flashes - Normal operation with call for heat. Three Amber Flashes - Normal operation, burner is on at end of thermostat cycle. Six Amber Flashes - Normal operation with call for heat pump heating. Any Red Flash - Fault condition. NOTE: 4 or 5 flashes may indi cate a blown fuse on the circuit board. Application Upflow Downflow Horizontal Top 1" 0" 0" Vent 0" 0" 0" Rear 0" 0" 0" Side 0" 0" 1" Front* 0" 0" 0" Floor Combustible Co

Theinstallationmustcomplywithregulationsoftheservinggassupplier, localbuilding, heating, plumbing, andothercodes. Inabsenceoflocalcodes, theinstallationmustcomplywithnationalcodesandallauthoritieshavingjurisdiction. B24.25” .56” .56” 20” 3” 23.8” .56” CombustionAirInlet2” DiameterVentConnectionOutletBDURINGINSTALLATION, DOORSMUSTREMAINONFURNACEWHENMOVINGORLIFTING. VentConnectionOutlet † Other airflows are available. see Tech Guide for all CFM options. * Cool Tap. ** Adjustment Tap. LED INDICATOR

If the furnace is equipped with NOx screens and is to be 7. To measure total static pressure, add supply duct pressure detailed information. used with LP (propane) gas, the screens must be removed to the return duct pressure, add pressure drop across the ‘A’ prior to start-up. coil, and add pressure drop across the filter. Ignore negative 2. Drip leg in the gas line must be installed. signs on the readings. 3. The furnace controls require correct polarity on the power 8. Inlet gas pressure shoul

Refer to “COMBUSTION AIR SOURCE FROM OUTDOORS and VENT AND SUPPLY AIR SAFETY CHECK” in these instructions for additional information and safety check procedure. 2. The duct shall be either metal, or a material meeting the class 1 requirements of CAN4-S110 Standard for Air Ducts. 3. The duct shall be least the same cross-sectional area as the free area of the air supply inlet opening to which it connects. 4. The duct shall terminate within 12 in (30.5 cm) above, and within 24 in (61 cm) horizonta

The equivalent length of the vent system is the total length of straight pipe PLUS the equivalent length of all of the elbows. The following rules must also be followed: 1. Long radius (sweep) elbows are recommended. Standard elbows may be used, but since they have a longer equivalent length, they will reduce the total length of pipe that will be allowed. Short radius (plumbing vent) elbows are not allowed. The standard dimensions of the acceptable elbows are shown below. 2. The maximum equiv

Overcurrent Device Amps 2 25 30 30 40 45 60 Min. Overcurrent Device Amps 3 20 20 20 25 30 40 Compressor Type Scroll Scroll Scroll Scroll Scroll Scroll Compressor Amps Rated Load 12.8 14.1 14.1 17.9 21.1 27.5 Locked Rotor 58 73 77 112 115 135 Crankcase Heater No No No No No No Fan Motor Amps Rated Load .8 .8 1.5 1.5 1.5 1.5 Fan Diameter Inches 22 22 22 24 24 24 Fan Motor Rated HP 1/8 1/8 1/4 1/4 1/4 1/4 Nominal RPM 1075 1075 850 850 850 850 Nominal CFM 2750 2800 3200 3600 3600 3700 Coil Face Area

Visit us on the web at Additional rating information can be found at versatile system of air conditioning. It is designed to be custom- matched with one of UPG’s complete line of evaporator sections, with each serving a specific function. Matching Air Handlers are available for upflow, downflow, or horizontal applications to provide a complete system. Electric Heaters are available, if required. Add-on coils are available for use with upflow, downflow, or horizontal furnaces and air handlers. WA